-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
900 Micron Buffer Fiber Thermal Stripper - TFS-900-250
-
Shanghai Fibretool Technology Co.,Ltd.
TFS-900 900um buffer thermal stripper design small, lightweight, easy to use and reliable, longitudinal peel, peel force is small, the high quality of stripped fiber; blade durable and easy to replace, using linear bearing guide and thermal stripping to ensure no damage to the fiber, easy to strip coating, stripping speed and other characteristics. With the fixture using the strip dual core optical fiber
-
Product
Wind Power Solution
ECO SUZLON
-
The ECO SUZLON is custom-made with firmware and fixtures designed specifically for Suzlon turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
In-Line RF Test Platform
AR925
Test Platform
This functional and RF test platform combines outstanding productivity with substantial equipment savings. The Faraday chamber of the fixture comes with an interchangeable cassette to minimize the testing cost of each new product
-
Product
G12 - 12 Module Solution
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm SMB
45-720A-511
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
Test Services
-
From Test Consultancy for new projects, to fixture program development, Terotest offer their experience and support to help you every step of the way. Terotest also offer a range of services to the existing ATE User including calibration and System Service options.
-
Product
In Circuit Test Service
-
In Circuit Test Program Development. Provide you with programming and fixture build as well as schematic review. Will order the fixture from one of our preferred vendors or any Fixture Vendor you prefer.
-
Product
Compact Tester
-
Designed for testing a family of products with similar functionality. A cost-effective solution for simple PCB architecture. Measurement system integrated with the adapter. Allows the use of interchangeable adapter inserts, including tandem type. Allows you to expand the scope of functionality. Optional interchangeable adapters (fixtures). Perfect for low-volume production
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
Testing Machine Fixtures
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
A device or setup designed to hold the device under test in place and allow it to be tested by being subjected to controlled electronic test signals.
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
Clamshell Type Mechanical Fixtures
Series 30
-
Semco’s GR Series 30 mechanical kits are an inexpensive solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility.
-
Product
Absolute Length Gauges For Measuring Stations And Multi-gauging Fixtures
ACANTO series
-
*High system accuracy: ±2 µm / ±1 µm*Serial data transmission*Interface: EnDat 2.2*Protection rating of up to IP67*Compact design for limited installation space*Various plunger actuation possibilities
-
Product
Stand-Alone Test Fixture
MA 2012/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 15,50 kg
-
Product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
RF Signal Generator
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
Shield Boxes
-
Concentric Technology Solutions, Inc.
CTS can provide a customized integrated RF Shield Box or RF Enclosure Test Solution for manual or automatic testing at an off-the-shelf solution price. Many companies make RF Shield boxes, RF Enclosures or DUT fixtures, but only CTS bridges the gap by providing a complete integrated RF Shield Box or RF Enclosure testing solution for providing the RF shielding needed for repeatability within your budget and schedule.
-
Product
Bending Stiffness Test Fixture
-
Q-Card’s bending stiffness fixture features splayed feet and aggressive no-slip rubber pads for stability. It is manufactured of aerospace-grade aluminum alloy with a hard anodized, scratch-resistant, durable finish to provide years of rigorous testing and trouble-free service.
-
Product
Receiver, G12, 12 Module, With 20" Platform, For Slide Mount (slide Kit Required)
310104334
Receiver
The 20” G12 Receiver is a slide-mounted receiver. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
Manual Fixture Kit
230356 – CMK-07
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Software Module with a Virtual Gage for Real-Time Inspection and Assembly
Verisurf Build
-
Verisurf BUILD is the industry-leading tool for real-time model-based inspection, tool fabrication, and computer-aided assembly.Inspect position and profile, set details and fabricate tools, jigs, and fixtures faster and at lower cost than any other process or software.Evolved and perfected from a large installed base at today’s modern aerospace, automotive, and industrial tooling manufacturers.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
CMP Mechanical Kits
CMP-XXX-HP
-
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
Product
In-Circuit Testing
-
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
Product
Bench Mounted Tester
Flex 10
-
The Flex 10 bench mounted ATE is the smallest ‘standard’ tester in our range. The system comprises a single unit, measuring 600mm x 360mm x 660mm. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
Product
Universal Test Fixture
CAM/GATE
-
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
Product
6TL10 Table Top Test Base
H71001000
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Testing Services
-
*Programmable Multipoint Tester*Over 8,000 programmable test points (DWV, Capacitance, Insulation Res., 2/4-Wire Resistance, etc.)*1500VDC / 1000 VAC Dielectric Withstanding Voltage (DWV)/ Hi-Pot (Programmable Dwell times)*Full Electronics laboratory complete with state of the art testing equipment*Custom Unit Testing (Designing of Specialized Test fixtures)*EMI Testing*Temperature and Humidity Testing*Shock Testing*Vibration Testing*Sand and Dust / Altitude Testing*Military Qualification Tests Performed
