Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
-
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
Product
Emulates Atmel T89C5111
FE-5111
-
* Emulates Atmel T89C5111 * 4K Code Memory * Real-Time Emulation and Trace * Frequency up to 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Non-Isolated
SC7
-
Module SC7 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications. SC7 is the same as SC1 except SC7 reallocates the pins used for CTS Flow Control as four (4) additional system grounds.
-
Product
VXS Backplanes
-
VXS (VME Switched Serial) represents an extension of the VME family according to VITA 41.0. This system is downward-compatible, so that assemblies with VME 96-pin connectors can still be used, while adopting the use of serial signals such as Gigabit Ethernet, PCI Express, Serial RapidI/O, and other fabrics.
-
Product
Hybrid & Electric Vehicle Dynamometer Testing
-
SAKOR Technologies Hybrid/Electric Vehicle Powertrain Dynamometer Test System (HEViDyne), winner of the SAE 2008 Technical Award for Hybrid/Electric Vehicle Testing Technology, is a comprehensive solution for performance, efficiency, and durability testing of all types of hybrid and electric vehicle drivetrains, including:*Hybrid assist (parallel hybrid)*Gasoline or diesel/electric (serial hybrid)*Fully electric vehicles
-
Product
PCI Express VXIbus Slot-0 Interface
ProDAQ 3030
-
The ProDAQ 3030 PCI Express VXIbus slot-0 interface is a C-size, register-based VXIbus module providing a direct connection from a PC to a VXIbus mainframe using the high-speed PCI Express serial bus. Together with any of the available host cards, the ProDAQ 3030 enables users to use a laptop, desktop, or server computer as an embedded controller. Optimized for low latency and high throughput, it provides a high-performance but cost-effective solution for a data acquisition system.
-
Product
Serial to Parallel Analysis Package
B4601C
-
Your system uses serial buses to communicate between ICs and transfer data to and from peripheral devices. Sifting through thousands of serial bits by looking at long vertical columns of captured 1's and 0's can be very tedious, time-consuming, and error prone. The Keysight Technologies B4601C serial to parallel analysis package is general-purpose software that allows easy viewing and analysis of serial data.
-
Product
JadeFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5983-317
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- VITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB and 5 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and synchronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
SAS (Serial Attached SCSI)
-
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
Product
Universal PCI, Eight or Four-port RS-232/422/485 Serial Communication Card
LPCI-COM Series
-
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis.
-
Product
6U OpenVPX PMC/XMC rear transition module.
EnsembleSeries™ RTM60P
-
*High-density connector and breakout cable to access to RS-232/RS-422 serial and 10/100/1000BASE-T Ethernet interfaces*Four 9-pin serial interfaces and four RJ45 Ethernet interfaces via the breakout cable*Standard VITA 57 FMC connectors that map to the PMC and XMC user I/O connections from the HCD6220 or HCD6410
-
Product
3U CompactPCI Serial Front Removable SATA Carrier for SSDs
SD8-STEEL
-
The SD8-STEEL is a peripheral slot card for CompactPCI® Serial systems. It includes a shuttle for 1.8 or 2.5” SSD or HDD drives. Signal integrity is optimized with 6Gbps SATA drivers. A push button ejection of the drive enables easy swap removal.
-
Product
WaveMaster Oscilloscope, 13 GHz Bandwidth, 4 Input Channels, 40 GS/s Max Sample Rate
WaveMaster 813Zi-B
Oscilloscope
Up to 20 GHz bandwidth and 80 GS/s sample rate.The most advanced oscilloscope user interface.The industry’s only true hardware 14.1 Gb/s serial trigger.Low Jitter Measurement Floor and exceptional timebase stability.Comprehensive set of serial data analysis, debug, validation and compliance tools.Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility.Integrated standard and custom measurements and math functions for unrivaled analysis capability.Multi-lane serial data eye, jitter and crosstalk analysis.Real-time de-embedding, emulation, and equalization.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
RS232/422 Strobe Mux III Card & Panel
9565-32
-
32 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 14.5" high x 13" wide x 1" deep (645 x 330 x 25 mm).
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Serial And Parallel Port For PCIe
DTA-2142
-
Serial and parallel interfaces for ASI and SD-SDI, supporting multiple electrical standards including M-LVDS and LVTTL. Clock rates up to 108MHz are supported.
-
Product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, CANbus, 2 LANs And DIO (2-in/1-out)
IFB112
-
The IFB112.supports the low power consumption NXP (Freescale) i.MX6UL ARM® Cortex™-A7 528MHz SoC. The design concept of IFB112 is aiming to meet the demands of mission-critical applications. The gateway controller with IP30-rated aluminum and steel enclosure supports an extended operating temperature ranging from -40°C to 70°C, a wide voltage range of 9V - 48V DC power input with terminal block, and has been designed to withstand vibration up to 5G. For system integrators with wireless communication needs, the IFB112 has one PCI Express Mini Card slot, one SIM card slot, and two internal antennas. It supports one serial port, two LANs and one CANbus port to enable fast and efficient data acquisition and communication. Its digital I/O port provides users with a convenience of digital devices connection.
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
Data Acquisition Module
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
LAN⇔RS-232C Conversion
SI-60F
-
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
Product
PCI to PMC Adapter/Carrier
PCIBPMC
-
1/2 Length Bridge Based PCI Adapter Carrier Card with PMC Mounting Slot. The PCIBPMC ( PCI Bridge PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCIBPMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit bus operation. The PMC user IO connector Pn4 is brought out to one of two connectors for access (DIN IDC or SCSI II). The signals corresponding to the PrPMC standard Ethernet and Serial lines can optionally be connected to the Ehternet and Serial port connectors at the top edge of the board.
-
Product
15" XGA, 64MB, 128MB(NAND), Serial X3, Ethernet
WOP-215K
-
ARM9™ 32-bit RISC processor with 64 MB SDRAM working memorySupports over 500+ PLC industrial communication protocolsBackup memory 128KB for retaining critical data or parameterSupports the HMINavi Designer development tool free on Windows 10Supports HMINavi Runtime data downloads through Serial, Ethernet, USB portNo limitation on the internal I/Os points used for variety applicationEasy to switch one application to different LCD sizes in secondsSupports operation in both landscape and portrait modePanel mount design ensures easy installation and IP66-rated front panel
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
CANbus Controller Standard Interface
PCI360
-
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
Digital I/O
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
Product
Serial FPDP HDL
-
Curtiss-Wright Defense Solutions
A serial FPDP HDL is available in-source or ported to specific host platforms under the FusionXF suite. The serial FPDP IP supports data rates of up to 2.5Gbps per channel. The IP is suitable for Xilinx Virtex-5 and Virtex-6 platforms. Contact Curtiss-Wright for alternative platforms. Licensing is on a per-project, per-site basis. License details are available from Curtiss-Wright.
-
Product
Chilled Mirror Transmitter
DewTrak II
-
The DewTrak II uses the chilled mirror dew point temperature condensation principle to determine the water vapor concentration in gas mixtures, and a platinum resistance thermometer to accurately measure that temperature. Outputs include 4 to 20mA, 0 to 5 Vdc, or 0-10Vdc and an RS232 serial port as well as electrically isolated relay contacts.
-
Product
HPLC Pumps
M1 Class
-
Applications include precise chemical metering, dispensing, and specific HPLC separations. Standard fluid path materials are Stainless Steel and PEEK. With 10 mL/min, 40 mL/min, and 100 mL/min versions, reaching pressures up to 2,500 PSI, these pumps capture the majority of typical laboratory fluid transfer applications. Features include interactive keypad control and Outlet Filter, RS-232 Serial and Micro USB 2.0 ports for complete PC control and status, as well as hardware for laboratory stand mounting. Having the smallest possible footprint for a high pressure pump, the M1 Class will easily integrate into any laboratory or industrial environment.
