Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
product
400MHz DDS Signal Generator
440A
The 440A generates a sinewave is via an RS232 serial interface. The frequency is accurate to 1.5ppm and can be locked to an external frequency reference. The phase can also be programmed with 14-bit resolution. It includes a Line Voltage AC Adapter and a CD containing windows software.
-
product
Intelligent CPCI Quad Industry Pack Carrier
CPCI-6713-4 IP
The board consists of private SDRAM and Flash memory attached to the 300 MHz TMS320C6713B DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is availablefor downloading programs into a non-volatile memory. A PCIbus connector provides the interface to the host computer. A serial port is available for debugging.
-
product
ANSI X3.28 to Modbus RTU Converter
Model 2399
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
product
Data Acquisition - 3U 3-Slot
DAQ-33CP0G
is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of military/aerospace data acquisition applications that require high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications Dual-Port Gig-E Ethernet.
-
product
Telemetry Bit Error Rate (BER) Tester
Reach Technologies Inc. Bit Error Rate Testers are designed for testing synchronous serial communications equipment, communications links and radio telemetry systems. In addition to several standard configurations, Reach also offers custom configurations, including multi-channel and mixed data rates.
-
product
VME Module
COM-1553B-3
The COM-1553B board gives the MIL-1553B designer an intelligent and versatile solution to multiplexed serial data bus design requirements. In applications that require the throughput and reliability of 1553B communications, the COM-1553B is a cost-effective system component with unsurpassed performance.
-
product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
product
rSSD SATA 3
RunCore Innovation Technology Co. Ltd.
RunCore rSSD RC0 series solid state drive compliant with Serial ATA Revision 2.6 and 3.1 specification and compatible with 3.0Gbps and 1.5Gbps interface rate. The rSSD family extends’s portfolio of high-performance, fully-integrated embedded solid-state drives.
-
product
Linear Power Supplies Programmable, Local or Digital Control, Ultra Low Ripple/Noise
Series MBT-G
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Low Profile PCI Express 1-Port
7106e
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
Serial FPDP Rugged Rackmount Recorder
Talon RTR 2756
- Designed to operate under conditions of shock and vibration- Complete Serial FPDP record and playback system- Up to 8 I/O channels in a single 4U 19-inch rugged rackmount PC server chassis- Removable SSDs- Up to 38.4 terabytes of storage to NTFS RAID disk array- Copper, single-mode and multi-mode fiber interfaces available- Real-time aggregate recording rates of up to 5 GB/sec in eight-channel configuration- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- RAID levels of 0, 1, 5, 6, 10 and 50- Optional N+1 redundant power supply- SystemFlow® GUI virtual instrumentation panel for fast, intuitive operation- C-callable API for integration of recorder into applications- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor
-
product
Universal Automated Programming System
4900
The 4900 is powered by the newest BPM 9th generation technology, which delivers the fastest programming speeds in the industry for MCU’s, eMMC HS400, NAND, NOR and Serial Flash devices. BPM 9th generation technology produces 200 MHz signals, allowing each byte of data to transfer in up to 2.5 ns. Up to 9 times faster than competing programmers. 3D Vision option inspects BGA, CSP, QFP, TSOP, SOIC and J-Lead devices for coplanarity, bent lead, pitch, width, diameter, standoff and XY errors.
-
product
Prototyping Kit
VXI-5502
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
product
RS232 Straight-Through Cable, DB-9 Female to DB-9 Male, 2m
183045-02
9-Pin Female DB-9 to 9-Pin Male DB-9 GPIB Serial Cable - The 9F-9M S10 Serial Cable, sometimes referred to as GPIB S10 Cable, connects and controls GPIB devices using the RS232 serial port. The 9F-9M S10 Serial Cable is offered in different lengths.
-
product
"Signal Transporter"
LTX-5520
The LTX-5520 enables the conveyance of sixteen independent channels of digital information over fibre optic links ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled at 50 mega-samples per second, multiplexed and transmitted serially over an optical fibre at a 1 Gb/s data rate.
-
product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
785831-33
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
PCI to PXI Remote Control Kit
41-921A-001-KIT
This kit provides a seamless connection between a control PC’s PCI interface and a PXI chassis. The PCI to StarFabric module (51-921A) resides in one of the controllers PCI slots and provides two independent StarFabric serial interfaces, each capable of driving a separate PXI chassis.
-
product
DSP Based Serial Communication Board
CPCI-ISC8
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
product
Ethernet, GPIB And USB To Serial Interface Board
ICS's Model 9006 is a multi-interface to serial board that adds Ethernet, GPIB and USB interfaces to serial devices or older instruments. Use with an embedded processor board to create smart instruments with multiple interfaces. The 9006's Ethernet port is VXI-11 compatible for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9006's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
product
3U CompactPCI Serial 5-slot SSL w/ RTM w/ Ethernet
1CPCIS-305-L210
3U CompactPCI Serial Backplane with 5 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 4x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 5, Ethernet full mesh.
-
product
GPIB-RS232, Serial, RS232 GPIB Instrument Control Device - Universal Euro 240VAC
779732-04
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Multiprotocol Serial Card
PCIe-ICM-4SM
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
product
PXIe-8842 2.6 GHz 6-Core Processor PXI Controller
788816-01
The PXIe8842 is an embedded controller for PXI systems that you can use for processor-intensive modular instrumentation and data acquisition applications. The PXIe8842 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, one Thunderbolt 4 port, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 58851
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUC (digital upconverter)- Four 800 MHz 16-bit D/As- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Powered VXS Crates
VXS - "VME-bus switched serial" is the new ANSI / VITA 41 standard which combines the 32-bit parallel VME-bus with high speed switched serial interconnect fabrics in order to increase the data transfer bandwidth to several GB/s.
-
product
PLD ISP Feature, GTE 10.00p
K8220A
The PLD ISP feature allows the test developer engineer to specify a configuration bitstream file in VCL digital test file, much like programming a Flash memory device. The PLD ISP feature supports multiple PLD configuration data formats are supported including. Serial Vector Format (SVF), Standard Test And Programming Language (STAPL), Jam, Jam Byte Code (JBC) object files.
