System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
In-Circuit Test System Repairs
Test System
Forwessun provides expert repair services for a wide range of Test Systems, helping you maintain optimal performance and extend the life of your equipment. Our team of skilled technicians quickly identifies and addresses issues, ensuring that your system is back in operation with minimal downtime. We handle both routine and complex repairs, offering comprehensive solutions to keep your systems running efficiently and reliably.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 102kΩ
40-298-134
Programmable Resistor Modules
The 40-298-134 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Remote Docking Fixtures
-
RTI offers a variety of docking interfaces including our Standard OctoPogo series with interchangeable alignment plates to third party test fixtures. RTI has developed many complete interface solutions, including everything required to interface to various test systems.
-
Product
Multiport Coaxial Switch, DC to 20 GHz, SP4T
87104B
Coaxial Switch
The Keysight 87104B multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87104B terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
Product
Test Tables / Test Consoles
-
Adaptronic test tables and test consoles are a decisive component of the adaptronic kit for the assembly of comfortable and high-quality test systems for the wiring test of manufactured cable harnesses of all types.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Extendable Version
SL1720A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development.
-
Product
DUT Boards
-
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
Product
Macro-Vickers Hardness Testing System
LV Series
-
LECO's LV Series Macro-Vickers Hardness Testing Systems offer an affordable testing system suitable for larger, heavier samples used in welding and other demanding applications. Models include analog and digital, with options to upgrade to automatic configurations.
-
Product
DC Voltage Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
DC test systems are used to test components and complete systems found in electrical power supply systems and operating on DC voltage.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
System Test
-
Testing a complete system is very different from unit and integration test. It starts with the V model that defines the system requirements, and this needs an effective system test capability that includes both the system and the environment around it. If the system has interfaces to the outside world, communications links or human control, these interfaces have to be tested.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 3.5Ω to 773kΩ
40-298-043
Programmable Resistor Modules
The 40-298-043 is a high density programmable resistor module with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Battery Testing System
C8000
-
The Cadex C8000 stands in a class by itself in flexibility and affordable price. Test SMBus batteries, monitor cell balance and capture load signatures to observe batteries with a unique load protocol. Add a thermal chamber, an external load bank, a safety circuit and alarm to form a command center and you begin realizing the unique qualities of this fine battery testing system.
-
Product
Motor Quality Control Test Systems
-
SKF Condition Monitoring Center
These rack-style motor quality control units are rugged, field-proven systems for testing stators and armatures in high-volume manufacturing environments. They combine the most common electrical tests into an efficient automated solution.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 52.4kΩ
50-298-133
Programmable Resistor Modules
The 50-298-133 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Digitaler I/O Mit 16 Kanälen
MDS
-
The static driver sensor module (MDS) is used to replace existing TS02 from previous MTS test systems. The possible pin extension allows to replace the systems MTS 200/210 (4 UCB with 4 MDS = 256 pins). A maximum of 1,024 MDS pins can be realized on the current MTS systems. Up to 4 MDS modules can be connected to one UCB (UCB03 or higher).
-
Product
PXI Precision Resistor Module 4-Channel, 1.5 to 3.55k
40-297-123
Programmable Resistor Modules
.This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Modular Test Systems
-
Whether thin film, thick film, MEMS, multilayer or bulk: With test systems from AixACCT Systems, you can characterize your piezoelectric materials both in development and during production with the greatest accuracy.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 2.5Ω to 1.51MΩ
40-252-044
Programmable Resistor Modules
The 40-252-044 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 1.51MΩ with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Force Measurement & Torque Measurement Test Stands
-
Mark-10 offers the industry's most extensive line of manual force measurement and torque measurement test stands. Test stands are useful in eliminating variability inherent in hand testing and can help to automate test processes. A wide range of capacities, loading methods, and configurations are available. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
Product
Backplane Test System
402LV
-
Very High Pin Count Level IV Backplane Test System. To ensure that Testronics maintains its leadership position as the premier supplier of backplane testers, we will be introducing our solution to testing high pin count / very large backplanes, the Model 402.
-
Product
Agile Signal Generators (UXG)
XSeries
-
Get a powerful building block, whether you need a dependable LO or a scalable threat simulator More accurately simulate multi-emitter scenarios for radar, EW and antenna test with the fastest switching, phase coherency, and extensive pulse-modulation Test sooner and increase confidence in EW system performance by generating complex signal simulations when you need them Increase the reliability of your test system: the UXG is a slide-in replacement for legacy fast-switching sources
-
Product
Radiator Test and Repair Stand, Type 1b (w/ Integral Flow Tester)
9401A
-
The Radiator Test and Repair Stand with integral Flow Tester is our most popular piece of radiator test equipment as it combines the functionality of a leak and repair stand with that of a flow test system, reducing both cost and footprint.
-
Product
Controlled Impedance Analyzers
-
HYPERLABS Controlled Impedance Analyzers can be used with various probes and adapters to quickly and reliably characterize impedance on PCB test coupons. These Test Systems are designed to comply with IPC-2141A standards for PCB coupon testing, and can be customized to meet specific customer needs.
-
Product
PXI Functional Test System
U8989A
Functional Test
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
Product
Memory Burn-In Test
-
The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies.
-
Product
SAS Protocol Test System
M124A
Test System
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
Matrix Switch Module
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
