System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
product
8 Gbit/s Read-Write Analyzer
RWA 4000 TDMR
Works with GSA 6044 digital signal analyzer to perform Two Dimensional Magnetic Recording (TDMR) measurements. RWA 4008 TDMR Read-Write Analyzer is a part of the new generation all-digital Guzik 4000 Series test systems. RWA 4008 TDMR requires Guzik signal analyzer GSA 6044 to provide a complete RWA TDMR solution for magnetic recording test applications.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
TDR Test System
GATS-310
The GATS-310 TDR test system provides you with the ability to test nets as down to less than 1/2" in length using Industry Standard Techniques.
-
product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope
780319-03
1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
product
Calibration
We also help to fulfil the recommended calibration cycles of the other measurement instruments within your test system. In case you can not go without the whole system we will find another solution like a change or loan of single devices.We also offer whole test system calibrations on-site as part of our preventive maintenance concept.
-
product
Test Automation System
RT-Tester
Verified Systems International GMBH
Designed to perform automated hardware-in-the-loop tests and software component test on process or thread level for embedded real-time systems. The functional components of RT-Tester can be structured as shown in the figure to the left. Please click on the small image to enlarge the picture. The System Under Test (SUT) denotes the object to be tested.
-
product
Saluki S8723X Series USB CW Power Sensor (9kHz - 40GHz)
S8723X series is a diode detector USB power sensor based on a USB 2.0 full-speed/high-speed adaptive interface. It has a wide frequency range and large power dynamic range. It can be connected to a computer or other electronic measuring instruments, easy to set up a power test system, particularly useful for field and other low-cost production line testing and power testing.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
RMC-8355, 2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI
782568-01
2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI - The RMC‑8355 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon E5620 quad‐core processors that support up to 96 GB of DDR3 RDIMM ECC RAM. The RMC‑8355 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8355 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
product
Self Test Application Adapter and Software
OTP2-Modul-Nr210
In order for the system to carry out a self-test, it requires a suitable adapter and software that is tailored to the test system. A self-test is often very helpful and recommended if a system has not been used for a long time or also to see whether the test system is working properly with the specified parameters.
-
product
High-Power, Rack-Mount Amplifiers
High-power, rackmount amplifiers utilize advanced power combining techniques to achieve high output power levels. These integrated amplifiers include advanced cooling capabilities and other customizable features. Though a focus on modularity, these rackmount amplifiers are ready for easy integration into a larger system or lab test bench.
-
product
Emission Measurement Systems
HORIBA develops and manufactures products and systems for testing of all types of engines: heavy-duty to small utility, onroad systems to non-road, marine to locomotive, automotive to aeronautic. Our extensive product line includes analyzers, analytical systems, dilution/ sampling systems, dynamometers and automation systems to assist engineers to evaluate and advance: exhaust gas and particulate emissions, engine performance, fuel economy, fuelcell reformer efficiency, other parameters of engine and vehicle.
-
product
3U Intel® Core™ i7-4700EQ Quad-Core Processor-Based PXI Express Controller
PXIe-3985
The ADLINK PXIe-3985 PXI Express embedded controller, based on the fourth generation Intel® Core™ i7 processor is specifically designed for hybrid PXI Express-based testing systems, delivering maximum computing power for a wide variety of testing and measurement applications.
-
product
PCI Precision Resistor Card 18-Channel, 1Ω To 239Ω
50-297-013
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Ferroelectric Test System
LCII
Precision LC II is an affordable Ferroelectric Tester for research labs. This system offers 5Khz at 9.9V and also comes in a built in 10V, 30V, 100V, and 200V option. This unit can also be expanded to 10kV for bulk ceramic testing. Vision Software is provided with the LCII Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choose from.
-
product
Modulation Distortion Up To 8.5 GHz
S930700B
S930700B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 8.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930700B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783283-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Automotive Electronics Functional Test System
TS-5020
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
product
Meter Test Board
MTB-3200
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
-
product
Benchtop/Portable Cable/Harness Wiring Test System
CKT1175-10
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
product
Slip Table Assembly
ST Series
The ST Series Slip Table Assembly is one of three base configurations offered by Unholtz-Dickie for its vibration test systems. It is ideally suited for sequential 3-axis test capability with minimized cross axis response; for testing heavy, oversized, or non-symmetrical loads; and for products where orientation with respect to gravity is necessary.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 102kΩ
40-252-034
The 40-252-034 is a programmable resistor module with 2 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Flammability Test System
COMP0804CAP
Active flammability test system according to IEC 60384-14 Ed4. For testing X & Ycapacitors up to 1uF. The test system includes control of the nominal AC supply via an integrated variac up to 1800V. Impulse amplitudes are programmable up to 8kV which covers all requirements. X1 capacitors are stressed up to 4kV, X2 and Y4 capacitors up to 2.5kV and Y2 capacitors up to 5kV.
-
product
PXIe-2524 , 128‐Channel, 2 A, Multibank, 1‐Wire PXI Multiplexer Switch Module
780587-24
128‐Channel, 2 A, Multibank, 1‐Wire PXI Multiplexer Switch Module —The PXIe‑2524 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in one of the following 1‑wire multiplexer configurations: 16 bank 8x1, octal 16x1, quad 32x1, dual 64x1, and 128x1. The PXIe‑2524 also features onboard relay counting for relay monitoring.
-
product
Signal Generators
Precision Test Systems manufacturers various signal generators. We can also supply other manufacturers or used signal generators. Our main signal generators are listed below.
-
product
Horizontal Battery Crush Nail Penetration Test Machine
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Horizontal Battery Crush Nail Penetration Test MachineApplication: Battery Module / Battery Pack / Battery System crush test, penetration test.Drive Mode: Electro-hydraulic ServoCrush Tool: Semi-cylinder, hemisphere (According to test standard)
-
product
Replacement Protective Cover, ICon, Receiver
310113460
The receiver protective cover is designed to protect your modules and contacts while the test system is not in use. A protective cover is included with the iCon Receiver. The receiver protective cover comes with a beaded chain and mounting hardware.
-
product
Embedded
Since joining the Industrial Computing group of Phoenix Mecano, we have the pleasure of partnering with some fantastic companies. As the saying goes, “it pays to know a guy who knows a guy.” Well, we know a guy or two (companies) with a long histories of embedded system development, testing and production.
