Current
See Also: Direct Current, Alternating Current, Resistivity, Flow, Inductance
-
Product
PCI Express
-
PCI Express (PCIe) is a highly successful SerDes interface that is used in computing devices spanning a wide range of applications. Currently in its fourth generation with on-going roadmap development for a fifth generation, the PCIe interface is undergoing major technical advancements that require state-of-the-art development and validation tools. For example, Gen4 PCIe devices operate at 16 Gbps per lane and are expected to deliver very low bit error rate (BER) levels even over constrained and lossy transmission channels (e.g. printed circuit boards).
-
Product
PXI Mixed Configuration Relay Module - 7 Cells Populated
40-138-AA-BB-CC-DD (7 CELL)
Relay
The 40-138 2A Relay Module with 7 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PXI 2A Multiplexer, 8-Bank, 8-Channel 2-Pole
40-614-004
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
50-635A-006
Multiplexer Module
The 50-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
50-635A-008
Multiplexer Module
The 50-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Professional Automotive Digital Multimeter
CT8027
-
Full autorange features. Large 4 digit LCD display with analog bargraph. AC/DC Voltage measurement up to 600 Volt. AC/DC Current measurement up to 10 A. Tachometer function with inductive pickup measures from 30 to 20000 rpm
-
Product
PXI 8 x DPDT Power Relays
40-130-002
Relay
Pickering Interfaces 40-130 DPDT Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. It is available in a choice of 8 and 13 relay versions and has voltage handling up to 220VDC/125VAC and current handling to 2A . Connections are made via a front panel mounted 50 or 78 pin D-Type connector.
-
Product
Programmable Micro-Ohmmeter
4300C
-
The 4300C is the perfect instrument for tackling ultra-low resistance testing requirements associated with motors, transformers, fuses, connectors, breakers, bonding/weld resistance, and many other applications. The 4300C Digital Micro-Ohmmeter measures a variety of low-resistance devices ranging in value from 100nΩ to 20kΩ. The flexible measurement format of the 4300C provides six ranges of user selectable test current (from 0.1mA to 10A) and three voltage sensitivity settings (20mV, 200mV, and 2V).
-
Product
Portable 4-Quadrant Power Amplifier
PIV270
-
PONOVO POWER's PIV270 Power Amplifier is equipped with feature of high power, large current, high voltage, high precision, high speed etc. It can meet different application on power and precision requirements.
-
Product
Multi Operational Surge Tester (MOST) Consoles
MC Model
-
Digital Surge, DC Hi-Pot & Built-In 3 Phase Test Selector Switch all-in-one versatile Tester. The DC Hi-Pot tester has separate panel meters for direct readout (voltage and current) so that no interpretation on the scope's display is ever needed and enables one to ascertain Polarization Index (PI) Test results.
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
Split type Pulse Current Sensor
CTF-05M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Through hole type CT.*Open collector output.
-
Product
Capacitor for DC Filtering
FIL1
-
Lifasa - International Capacitors, SA
FIL condensers are specially designed for use in direct current sources and their functions are to filter the alternating output ripple and protect the line from instantaneous peaks and surges of tension.
-
Product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
Standard 0.39 (11.00) - 1.39 (39.00) Non Replaceable General Purpose Probe
MEP-20G
General Purpose Probe
Current Rating (Amps): 2Average Probe Resistance (mOhm): 50Test Center (mil): 25Test Center (mm): 0.635Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 750Overall Length (mm): 19.05Rec. Mounting Hole Size (mil): 20.5Rec. Mounting Hole Size (mm): 0.52Rec. Mounting Hole Remark: 20.5 to 21.5 mil / 0.52 to 0.55 mmRecommended Drill Size: #75 or 0.52 mm
-
Product
Battery Extra Load Units
BXL Series
-
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
Product
CTR Test Fixtures
-
Designed to hold electronic components or assemblies in place during testing, particularly for verifying the Current Transfer Ratio (CTR) of optocouplers.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Lightning Surge Simulator
LSS-720B
-
Voltage surge test (1.2/50µs) and current surge test (8.2µs) specified under JEC-210 and 212 standard. (JEC: Japanese Electrotechnical Committe)High voltage surge test up to 20kV and high current surge test up to 4000A (30kV/6000A model available)
-
Product
Astronomy Solutions
-
For more than 40 years, Thales has delivered high accuracy optics for ground-based Astronomy all around the world. These optics range from single, but challenging, unmounted optical components up to fully integrated opto-mechanical systems. Our design heritage and past experience in this field cover the design, manufacture and AIT activities of many optics and sub-assemblies used in Telescope instrumentation, such as focal plane assemblies as well as the direct production of telescope mirrors themselves. Several major achievements of Thales ground-based Astronomy products were the Optical wide field corrector for the Dark Energy Survey (lien), the Reference Body for future Deformable Secondary Mirror of the VLT (lien) and different challenging spectrograph optics (Collimator and Cameras) for different Observatories (lien). One advantage Thales has with this activity is that most part of the manufacturing steps involved (i.e. opto-mechanical design, milling/grinding, lightening, polishing and coating) are directly under our control in our own facility. Our current capabilities for the production of optics for ground-based Astronomy are from a few centimeters size up to 2 meters. Thanks to the continuous efforts in R& D and investments into new production machines, Thales is now ready for future industrial challenges including the optical production of some key elements of the E-ELT, GMT and TMT programs.
-
Product
PXIe High Voltage Device Power Supply - 2 Channels Per Card, 18-bit Voltage Programming Resolution and Measurement Resolution
33021
Power Supply
Max. 48V DC output with 2 channels per card, 12V-48V independently Programable voltage level, Max. 250mA current per channel
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
Product
BPLT-25 Long Travel Bead Probes
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cyles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
Motherboards
-
ITC currently manufactures over 100 different motherboard types, including interfaces to all major brands and types of testers. Additionally, ITC has the ability to quickly design and manufacture motherboards for any new tester interface including custom probe cards.
-
Product
High Accuracy Clamp Leaker
-
Leakage Current Clamp Meter, Car Standby Current Clamp Meter, Car Inrush current Tester, Car Charge Current Tester. It is specially designed for online measurement of AC/DC leakage current, current below 600V by adopting up-to-date CT technology and digital integration technology. It is especially suitable for measure car standby current, leakage current, inrush current. It is a product with the characteristic of relatively small size, high accuracy, strong anti-interference capability and automatic shifting.
-
Product
Premium 4.49 (127.00) - 12.00 (340.00) High Performance Lead Free Probe
LFRE-25I15-12
ICT/FCT Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Adapter
EXC-1553UNET/Px(S)
-
The EXC-1553UNET/Px is an intelligent, single - or - dual channel, MIL-STD-1553 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.The EXC-1553UNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Junior Set and Kits
-
Contents* AM-510-EUR (Digital multimeter)* ACD-10 PLUS (Digital current clamp)* TPP1-C1 (contact thermometer)* EU-200 (test lead set with 2 leads), 2 test prods (4 mm), 2 crocodile clips (CAT III/1000 V)* Hard carrying case
-
Product
Earth Fault Detector
K-3838
-
Kongter Test & Measurement Co., Limited
Kongter’s K-3838 earth fault detector is the updated model which is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems where electrical cables have breakage and current lost to ground. It will save you from long time unnecessary troubleshooting and helps to increase the reliability of your electrical equipments. Our unique technique makes it safe and fast to handle earth fault in DC systems that are working online.
-
Product
High Temperature Operating Life
7000 Series
-
With ever decreasing geometries, the way we perform HTOL requires careful consideration. In lower geometry device leakage currents are not only higher but vary greatly. Temperature control at DUT level – required to achieve correct junction temperature at every DUT. For higher geometries, HTOL can be performed in a more traditional way but with devices consuming more power, the ambient temperatures required varies greatly. Multiple temperature zones are required – multi zones system or multiple smaller HTOL systems.
