Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
QFP-to-PGA JEDEC 132-Position, 0.025 [0.64] Pitch Adaptor
95-132I25
-
QFP to PGA Adapter for JEDEC 132 Position, .025 [.64] Pitch. Reduce costs by using less expensive QFP packages to replace PGA footprints in existing designs. Pins are mechanically fastened and soldered to board using Aries patented process, creating a reliable electrical connection and rugged contact.
-
Product
Signal Generators
ZTX-Series
-
RPG's Signal Generator Extenders allow high performance frequency extension of microwave sources into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. These modules combine high test-port power with low phase noise to offer exceptional performance. Contact RPG to discuss Signal Generator Extenders configurations that will gain the best performance for your application.
-
Product
Phase Sequence Meters
-
Phase sequence meter is used for detecting the sequence of the supply in three-phase electric circuits. Since the direction of rotation of three phase electric motors can be changed by changing the phase sequence of supply. And also the correct operation of measuring instruments like 3 phase energy meter and automatic control of devices also depend on the phase sequence. Different types of phase sequence testers are available in today’s market like contact or non contact, static or rotating, etc., in a wide range of voltage or power ratings.
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 64 Position, w/ Right Angle Contacts
510104187
-
Primary mating module 510108101. (May mate with other ITA modules, as well.)
-
Product
G6x - 9 Module Solution
-
This 9 Module Solution provides versatility in the same small footprint as the G6. This high-density Interconnect can simultaneously engage up to 1,920 signal contacts. The ability to add 3 iCon modules into the interface design provides up to 25% more I/O. The ITA has a unique, removable EMI shielded cover which allows easy access to modules and contacts.
-
Product
Signal Conditioners
SC-7400
-
The SC-7400 handles a variety of temperature and process inputs and offers combinations of analog and relay contact outputs. All parameters - such as input and output range, set-points, deadband and burnout - are customer-selectable via software.
-
Product
Industrial Vibration Sensor
IVS-500
-
The new IVS-500 Industrial Vibration Sensor is the key to fast acoustic quality inspection, structure-borne noise analysis and reliable pass-fail decisions. This Laser sensor measures reliably, in demanding industrial environments, without contact and therefore without wear and on virtually all surfaces. Costs and yields are therefore optimized by reducing false rejects in the production and assembly process. The simple setup and ruggedized sensor design of the IVS-500 enable a smooth integration into production test systems. Complemented with the software tool QuickCheck, Polytec offers a comprehensive solution for reliable pass/fail analysis.
-
-
Product
High Altitude Wiring Clamp
-
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
Godzilla High Current Probe, 100 Amp
HC375
-
Current Rating (Amps): 100Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 360Full Travel (mm): 9.14Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,110Overall Length (mm): 78.99
-
Product
Micro-Ohmmeters
RMO-G Series
-
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing personnel.The RMO800G is the most powerful portable micro-ohmmeter on the market with 800 A output current. RMO200G is our best seller in the USA. A user can choose the appropriate model depending on the output current requirement, from 100 A (RMO100G) to 800 A (RMO800G).We use an unbreakable plastic case with IP67 protective rating (with closed lid) for instruments’ housing. Although very portable and lightweight, RMO-G micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents. Consequently, it enables the usage of thinner/longer test cables. RMO-G generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. During the testing, it increases current before measuring and decreases current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.Special current clamps measure a current through groundings when the instrument tests in Both Sides Grounded conditions. The instrument itself powers these clamps. If even higher safety level is required, the Remote Control feature enables the operator to perform measurements from distant locations.RMO-G instruments can store up to 500 measurements in internal memory. Also, they have a built-in thermal printer and USB flash drive available as an option. An additional option is the built-in High Precision module suitable for measurement of very low resistance, in the range from 1 to 30 µΩ, with 0,01 µΩ resolution.Our free DV Win software communicates with the RMO-G micro-ohmmeters via USB or RS232 interface. It allows a user to run the test remotely from a PC. Also, a user can download test results, analyze and generate fully configurable test reports through the software.
-
Product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
-
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Tachometers
-
Labs use this high accuracy unit to check speeds of centrifuges, motors, or stirrers. Five digit LCD is a vivid ½-inch high display. Tachometer takes only three seconds for most readings. A unique memory feature permits recalling the highest, lowest, and last reading. Unit is extremely easy to use; operation may be learned in one minute. One end of the unit provides contact readings with a rotating spindle.
-
Product
Tool, Adapter, Holding Fixture Adapter AT-1319-29
910121149
-
Used with Raychem holding fixture to aid in the solder process for Mini-Coax Solder sleeve contacts. Both fixture and adapter are included in Solder Kit Part # 910121144.
-
Product
Couplers, Repeaters, Bus Switches, Connectors, Cables & More
-
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
Product
LVDT With Unguided Armature On Both Sides
-
INELTA Sensorsysteme GmbH & Co. KG
The amature is attached to the application, but still moves free inside the LVDT. The correct axial alignment is important. The pushrod moves without any contact.
-
Product
Wafer Prober
Precio XL
-
Fully automated 300mm wafer prober. The system achieves high productivity, excellent contact performance, improved cleanliness, and short lead time, and offers a number of high value-added functions as options.
-
Product
Signal / Mini Coax, Module, ITA, TriPaddle, 90 Series, 16/16 Position
510108210
-
This module can accommodate certain VPC mini pneumatic contacts, but cannot be fully populated in all 16 positions with them. See specific product drawings for applicable limitations. For further assistance please contact a Field Application Engineer. Primary mating module 510104243.
-
Product
Receiver, G6, 6 Module, Keying Feature
310104318
-
The Receiver for the G6 is equipped with keying, a locking handle and nickel plated steel slides that engage up to 1,440 signal contact points. It allows a high amount of I/O within a compact and rugged device.
-
Product
Leaf Wetness Sensors
-
Campbell Scientific offers two types of leaf wetness sensors to measure the wetness of leaves: surface contact and electrical resistance. Surface contact sensors measure the electrical resistance of a water film on their surface. Electrical resistance sensors imitate the characteristics of leaves and measure the dielectric constant of their upper surfaces.
-
Product
Extraction Tools
-
VPC has specific extraction tools designed for each type of contact. Consult the procedure sheets on this page for detailed instructions on each tool's use. Correct tool use is crucial to prevent damage to contacts and modules.
-
Product
Pneumatic Contacts
-
VPC offers a range of pneumatic contacts that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
-
Product
Static Field Meter
-
This contactless precise electrostatic field meter can immediately sensor the static voltage on a charged body without contact. The measuring range is 0.010kV ~ 20.000kV with the sensing distance 1 inch (2.54cm). The meter provides alarm function for prompt.
-
Product
Backplane Twinax Connectors
-
We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.
-
Product
8-Channel Relay Output Board With Housing for Mounting on a DIN Rail
PX8500-G
-
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
Product
Shrinkage Template Scale
-
TESTEX Testing Equipment Systems Ltd.
Shrinkage Template Scale, suitable for all shrink testing standards. Shrinkage Template Scale complies with AATCC 135/150/160/179, BS EN 3759, ISO 3759, etc. Welcome to contact us if you have any problems about fabric shrinkage test method.
-
Product
Gold Probes
4900 Series
-
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
