Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Fixed Attenuator Pads
-
SemiGen RF/microwave fixed attenuator pads feature precise resistor films and superior metalization resulting in superior performance and consistency. Our advanced thin-film technology allows our parts to have full side wraps for SMT installation and a complete grounding backside for ease in attachment, as no ground bonding is requried. Top side contacts for the input and output make these ideal for standard RF/microwave assembly techniques. They are available as MIL PRF 38534 “H” & “K” space screened units. Custom values are easy to fabricate and design allowing users to design in a specific value of choice.
-
Product
PXI 48 x SPDT Power Relay Module
45-157-001
Relay
The 45-157 SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC.
-
Product
Electric Testing
-
Our Capabilities*Dielectric Withstand*Hi-Potential Testing*Voltage Drop*Contact Resistance*Gate Leakage*Insulation Integrity*Dielectric Integrity
-
Product
Tool, Kit, High Power, Receiver and ITA, Crimp
910102116
Tool Kit
This crimp tool kit contains a pneumatic crimp tool, plus locator and die set specific to high power contacts.
-
Product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Signal Contact (Receiver)
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)
-
Product
PXI Dual 8 Channel Switch Simulator
40-485-121
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Certified Sanitary Inline Refractometer | 2″ Tri-Clamp
VIP2-3A
-
3-A Sanitary Refractometer for Food & Product Safety: Driven by concerns over food and product safety in the dairy, food, beverage, and bio-pharmaceutical industries, 3-A certified sanitary refractometers must meet exacting hygienic standards before they are awarded certification, one of the top honors attainable in the field of refractometry. Needless to say, refractometers carrying the 3-A seal meet the highest level of professional standards for the protection of public health by offering the maximum degree of protection against food or product contamination, resulting in product contact surfaces that can be easily cleaned and sanitized.
-
Product
Diaphragm Operated Pressure Switch
1000W
-
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
Product
01 With Pins For PCB | 12 Positions | M10
01-1xxx-20/70xx-12-N
-
This compact 12-position rotary selector switch is designed for high-density PCB mounting. Featuring a robust M10 threaded bushing and a 6mm stainless steel shaft, it provides a precise 30° indexing angle and is rated for 25,000 switching cycles. Its gold-plated contacts ensure high signal integrity, making it ideal for industrial controls and medical instrumentation where space is at a premium but reliability is critical.
-
Product
PXI Single 16 Channel Switch Simulator
40-485-221
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Atomic Oven
-
Atomic oven with collimated output for ultra-high vacuum systems, loaded with Sr, Yb or Ca. The oven provides superior heat isolation while achieving high atomic flux. Its low power consumption results in exceptionally low pressures during normal operation for temperatures up to 650 °C. The chamber is shipped in an ultra-high vacuum storage chamber supplied by AOSense. Customers can provide AOSense with a previously purchased storage chamber for repeat orders. Please contact us for more information.
-
Product
IBM PC-XT, Vectorbord Plugbord
4613-3
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT M3K+
-
SCOT M3K+ measures and displays CLOSE, OPEN and CLOSE-OPEN times of Main contacts of 3 poles connected end to end, simultaneously. Ideally suitable for CBs with single break per pole.
-
Product
Low Noise Amplifiers
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don’t compromise and get technology from Kuhne electronic!
-
Product
PXI High Density Matrix Module, 32x8, 1-Pole, 2A, 60W
40-586B-001
Matrix Switch Module
Our model 40-586B, along with the following models 40-584, 40-585A, 40-587A are high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays.
-
Product
Laser Microdissection LMD
-
Is a contact- and contamination-free method for isolating specific single cells or entire areas of tissue from a wide variety of tissue samples.
-
Product
Ethernet to Relay Interface Boards
Model 8064 OEM
-
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
Product
Mini Power, Contact, Receiver, 65 Amp, 8 AWG
610116112
Power Contact (Receiver)
Primary mating contact 610115124. (May mate with other ITA contacts, as well.)Mini Power contacts carry up to 65 amperes continuous current. Maximum resistance is 1 Milliohms.
-
Product
Custom Compression Blocks & Spacers For Solid-State Battery Test Cells
CEP1
-
Precision-machined titanium alloy electrode posts, compression blocks, and spacers for solid-state battery test cells and electrochemical research. Available in custom sizes and configurations, these components provide stable mechanical support, reliable electrical contact, and excellent corrosion resistance.
-
Product
Optical Encoders
-
Rotary encoders are ideal for use as digital panel controls or position sensing devices in a wide range of applications where digital circuitry is used. These devices are available in contacting and optical types and in various resolutions. Some models are available with push momentary switch and detents.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Signal Contact (Receiver)
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)
-
Product
Network Sensor Interface for USB Pressure Transducers
SI314
-
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
-
Product
KV CAPS
500 V
-
Macom Technology Solutions Holdings Inc.
The MACOM KV CAPSTM Si high voltage capacitors feature very high working voltage ratings, very low loss and excellent stability by virtue of their novel internal construction and very high-quality dielectric layers. These capacitors are available as unpackaged chips. The chips have gold bonding surfaces on both terminals to enable excellent bonding and minimum contact resistance.
-
Product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
Test System
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Temperature Sensors
-
Universal temperature measurement for liquids and gasesWith its product portfolio of screw-in and insertion thermometers as well as temperature switches SICK offers high-quality solutions for contact temperature measurement in liquids and gases. The devices can optimally be adapted to meet individual requirements through its various insertion lengths and the flexible mechanical configuration possibilities.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
Coax, Module, Receiver, 75 Ohm, 90 Series, 32 Position
510104249
Receiver Module
Primary mating module 510108179. (May mate with other ITA modules, as well.) *Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS HL
-
Optik Elektronik Gerätetechnik GmbH
Measuring instrument for contact angle and surface free energy, special solution for semiconductor technology for wafers up to 300 mm.
-
Product
Enclosures
-
VPC offers a variety of options to customize standard enclosures to meet any application need. Use VPC's Customer Wirelist Template to quickly communicate your overall requirements. VPC can provide options such as cutouts, secondary connectors, silk screening, engraving, and much more. Contact a Field Application Engineer for assistance designing a custom enclosure to meet your test needs.
-
Product
H.V. Probe Meter
PD-40AM
-
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
