Response
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm
50-294-031
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Broadcast Combiners
RFS offers a comprehensive product line of FM combiners to suit a wide range of applications. The balanced (or constant impedance) bandpass design offers an expandable system that is built in a modular form enabling extra stations to be added at a future date. This configuration provides state of the art performance with the best frequency response and isolation attainable.
-
product
32-CH Discrete Output Daughter Board Module
HSL-DO32-DB-N
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type outputs*Photo couple isolation voltage: 2500Vrms*Output switching capacity: Single channel 500mA; all channels 60mA at 24VDC*Output response time:ON OFF: 180µs, OFF ON: *1.2µsTerminal Base:HSL-TB64 or HSL-TB32U-DIN
-
product
Active Filter
J2190A
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8493A
The Keysight 8493A coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
DH Series High-Sensitivity Solder-In Tip, 30 GHz BW, 2.0 Vpp Range
DH-SI-HS
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Pyranometer Negligible thermal gradient zero-offset
CMP 22
CMP 22 has all the features of CMP 21 but uses very high quality quartz domes for a wider spectral range, improved directional response, and reduced thermal offsets. Because of the high optical quality of these domes the directional error is reduced below 5 W/m. Kipp & Zonen is confident that CMP 22 is the best Pyranometer currently available.
-
product
Panel-mounted HIL Power Amplifier
PAC60Ci
PAC60Ci is the six-phase real time simulation amplifier, with maximum RMS phase current of 30A and maximum output power of 450VA. This current amplifier is possessed of high accuracy and fast liner response.
-
product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
product
High Voltage
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules. The flexible high voltage design platforms and responsive management structure enable us to offer an economically viable custom build. High voltage power supplies from ETPS are used in a variety of applications ranging from electron acceleration systems and mass spectrometers to magnetrons, x-ray and nuclear research.
-
product
Silicon Based Thermopile Detector: 4 Channels
ST120 Quad
A four-channel silicon-based thermopile in a TO-5 package. Each small active area is 1.2mm x 1.2mm . Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Server Monitoring Software
Motadata is an integrated server monitoring software & tool that delivers insightful details of all critical server performance parameters like hard disk capacity, CPU utilisation, memory utilisation and bandwidth utilisation from an intuitive web console. Our server performance monitoring allows a sysadmin to stay on top of server downtime and performance issues. This server monitoring software has the capability to monitor all types of IT infrastructure servers in both consolidated and distributed workload conditions. Identify server performance issues like resource utilisation, application downtime and its avg. response time.
-
product
Multiphoton Laser Scanning Microscope
FVMPE-RS
The Olympus FVMPE-RS multiphoton imaging system is purpose-built for deep imaging in biological tissue, aimed at revealing both detail and dynamics. Innovative features for efficient delivery and detection of photons in scattering media enable high signal-to-noise ratio acquisition. This translates to bright images with precise details — even from deep within the specimen. High sensitivity is matched with high-speed imaging to capture rapid in vivo responses. For advanced applications, dual-wavelength excitation extending to 1300 nm is available. Independent control of visible or multiphoton laser light stimulation and the ability to synchronize with patch clamp data are also possible.
-
product
UV A Radiometer
UVS-A-T
The UVS-A-T has a broad spectral response optimised for precise measurements of atmospheric UV-A irradiance.
-
product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Programmable DC Power
TS Series
The TS Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power''''s rugged current-fed power processing, enables confidence in even the most demanding applications.
-
product
High-accuracy Dual-channel Programmable Battery Simulator
N8352 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8352 series is specially designed for the R&D and testing of portable, battery-operated products , such as Bluetooth headsets, mobile, AR/VR smart terminals, electrical tools, etc. The current flows in both directions and can be used as either a power supply or a load. N8352 is easy for operation with touch screen and UI design. The output features are comparable to actual batteries, with fast dynamic response, no overshoot in voltage rise and fall, and stable waveform. The resolution is up to nA level, which can test the loop static power consumption, etc. N8352 can be widely used in the area of consumer electronics testing.
-
product
Modal tests
Modal Testing and Modal Analysis - SIMO, MIMO, and ODSEffective and affordable modal testing and analysis solution for SIMO, MIMO, and ODS testing methods. The modal test is an indispensable tool to determine natural frequencies and mode shapes of any structure. With our solution, you are able to excite the structure with an impact hammer or modal vibration shakers and easily measure the responses. Import or draw your geometry for rich visualization and animation of your structures.
-
product
Nano Science Instruments
Today nano technology has spread all over the world and this branch of science flourish will more in coming time. Nanoscience laboratory equipments used for various purposes, thus it is necessary that the instruments have Trademark, Design Registration and Copy right for quality assurance. Thus we have taken the responsibility to deliver good quality of nano science instruments which are easy to handle and have a long life. In fact we are the manufacturer and distributor of equipments used in nano science like:-
-
product
Acoustic Noise
American Environments Co., Inc.
A Test Specimens can be evaluated in two different modes in reference to acoustic noise: The Test Specimen's response to acoustic noise and the Test Specimen's generation of acoustic noise.
-
product
Solar Array Simulator
G5.SAS
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
product
COM Express Basic Size Type 6 Module with 11th Gen Intel® Core™, Intel® Xeon® and Intel® Celeron® Processors
Express-TL
ADLINK’s Express-TL COM Express Type 6 Basic size module is based on the 11th Gen Intel® Core™, Xeon® W and Celeron® 6000 processor, and is the first COM Express module to support PCI Express x16 Gen4, effectively doubling the bandwidth of previous generation COM Express modules. With a combined 8 cores, 16 threads, and up to 128GB memory, the Express-TL brings uncompromised system performance and responsiveness to your solution. Featuring brand new Gen 12 Intel® UHD Graphics and Intel® AVX-512 Vector Neural Network Instructions (VNNI), the Express-TL provides AI inferencing performance as much as 3X higher compared to previous generation non-VNNI platforms. The integrated Gen 12 Intel® UHD Graphics core can be configured to support one 8K independent display or four 4K independent displays (HDMI/DP/eDP). In addition, legacy display interfaces such as LVDS and analog VGA are still supported as build options. Key features for today’s applications are support for 2.5 GbE and USB 3.2 with transfer rates of up to 10Gb/s that can transfer image data from cameras faster than previous generation products. Combined with 8 processor cores at 25W TDP, Intel® AVX-512 VNNI, Intel® OpenVINO™ toolkit and Intel® UHD Graphics, the Express-TL is well suited for AI at the edge applications (AIoT/IoT).
-
product
Oscilloscope Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Oscilloscope for transient vibration signals*Displays the time response of vibration acceleration and VM-SCOPE+ also for velocity and displacement*Suitable for shock and drop testing of packagings and other products *Memory for 110 s post-trigger and 1 s pre-trigger real time signal recording*Two measuring cursors*Export function for bitmap and text*Up to four signals per window*One VM-SCOPE license can be operated simultaneously up to four times with different settings *Measurement of decay time*Measurement of HIC (Head Injury Criterion)*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External Messengers *Offline measurement
-
product
Water Level Controller with Timer & Overflow Sensors
IM1730
Ajinkya Electronic Systems provides water level controller which is most popular in housing societies. Water is a precious natural resource and it’s our social responsibility to save water whenever and wherever possible. In cities we get treated water and which makes it more precious. So there is a need to use this resource judiciously and carefully. In societies there are overhead tanks which gets filled periodically from the underground tank. The prosess requires man power for timely switching off the pump to avoid dry running as well as overflow of the water. The water level controller for societies offers a smart solution for pumping of the water to overhead tanks in buildings
-
product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm
50-293-031
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Cyber Protection System
Raytheon’s Cyber Protection System enables enterprises to go beyond traditional CSOC monitoring and establish a response center capable of situational awareness, proactive defense and rapid response. Cyber test ranges: Test the cyber resilience of hardware, software, and networks. Penetration/Malware/Forensics Fly Away Kits: Provide mobile environments to perform testing and analysis at remote facilities. Lab environments: Analyze malware, perform penetration testing and conduct forensics at enterprise scale so analysts can determine the best way to manage them.
-
product
Microphone Preamplifier
426B03
Performance: Nominal Microphone Diameter:1/4"Frequency Response: (0.1 dB) (re 1 kHz)5 to 126000 Hz5 to 126000 Hz Frequency Response
-
product
OEM CCD Camera
Syncerity BI-NIR Camera
The TE-cooled back illuminated 2048 x 70 CCD Camera combines affordability, performance and versatility for OEM applications. With peak QE of 84% @ 700nm and 20% at 1050nm, Syncerity BI-NIR offers a relatively broad response and addresses multiple applications. In the near-NIR, this detector is a much lower cost alternative to a deep depleted CCD, with no etaloning. Syncerity’s flexible design allows our OEM-dedicated team to quickly adapt the camera for industrial requirements, ranging from alternate CCD chips to electronics
-
product
Non-contact Sensors
SENSOR NAVI
The easy system check is a function that allows easy checking of the compatibility or incompatibility between products and accessories, but does not guarantee all combinations.- Since the information provided through this system consists of approximate estimates, Mitutoyo declines any responsibility regarding damages that may arise from such information.
