Response
-
Product
Radiometer Spectral sensitivities precisely adapted to the human skin
UVS-E-T
-
The UVS-E-T has a spectral response that is adapted to the erythemal (sunburn) action spectrum of the human skin (CIE 1987 weighting). Hence, this radiometer collects information of medical and public concern: UV Index, UV Erythemal dose and dose rate.
-
Product
Very Low Pressure Variable Reluctance Sensor
DP103
-
The Validyne DP103 is designed for exceedingly low differential pressure measurement applications where high accuracy is required under rough physical conditions. With full scale ranges down to -0.008 psid (-0.56cm H2O), this instrument is being used in the measurement of very low flow rates of gases where symmetrical pressure cavities are required for dynamic response. It is also used in very small leak detection and pressure null detection systems.
-
Product
Digital Meteorological Sensor
ZET 7023
-
The ZET 7023 weather sensor is a measuring unit with two in-built sensors one of which is responsible for measuring relative humidity and temperature, and the other one, for atmospheric pressure measuring.
-
Product
Preamplifiers
AH-series
-
A broad mix of in-line preamplifiers and accessories are offered to enhance hydrophone measurements by increasing the gain, preserving the flatness response, extending the dynamic range, and minimizing reflections.
-
Product
Photometric Probes for Illuminance
LPPHOT03… Series
-
The probe LPPHOT03 measures illuminance (lux), defined as the ratio between the luminous flux (lumen) passing through a surface and the surface area (m²). The spectral response curve of a photometric probe is similar to the human eye curve, known as standard photopic curve V(λ). The difference in spectral response between LPPHOT03 and the standard photopic curve V(λ) is calculated by means of the error f’1.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Light Meters
LXP-2
-
The digital light meter is a precision instrument used to measure illuminance (Lux, footcandle) in the field. It is meet CIE photopic spectral response. It is fully cosine corrected for the angular incidence of light. The illuminance meter is compact, tough and easy to handle owing to its construction. The light sensitive component used in the meter is a very stable, long-life silicon photo diode and spectral response filter.
-
Product
Seismometers
-
SI value, the so called “velocity response spectrum”, is one of the standards to express an earthquake''s destructive power against structures. SW-74SI is an advanced model equipped with alarm output to 10-step and SI value output.
-
Product
Handheld Wireless Transmitter
HHa
-
The HHa Digital Hybrid Wireless handheld transmitter represents an elegant solution for a variety of wireless microphone applications including live performance, broadcast, AV rental and houses of worship. The HHa incorporates many advanced features to provide high-quality speech and vocal reinforcement. Along with providing peerless audio quality with wide frequency response and dynamic range in 400 Series and Nu Hybrid Modes, the technology used in the HHa includes compatibility modes for Lectrosonics 200 Series, 100 Series, Mode 3, IFB receivers and some systems from other top manufacturers. Newer Digital Hybrid transmitters only have NUHYB, IFB and Mode 3
-
Product
Active Scanning Technology
-
ZEISS invented scanning in response to the drawbacks of single-point measurement nearly 50 years ago. This game-changing development enables the capture of thousands of data points within just a few seconds for truly reliable tactile quality assurance. It also saves time and money by delivering the high throughput and accurate results that are vital for manufacturing.
-
Product
Double Bellows Differential Pressure Switch
DP
-
Two opposing bellows in the Model DP differential pressure switch result in maximum sensitivity, quick response to changes and good vibration resistance. Choice of brass or 316 stainless steel assures broad media compatibility. Setpoint adjustment is easy thanks to external knobs and large, clear scale reading directly in psid.
-
Product
Time Domain Analysis
S93010A
-
The time domain capability allows you to measure the time domain response of a device. The analyzer can transform frequency domain data to the time domain or time domain data to the frequency domain.
-
Product
Power Limiter
-
RF Lambda’s power limiters are used to protect downstream RF components and equipment. Both active and passive models are available with fast response time and high power handling.
-
Product
External Temperature-40 to +125C
TGIS-0020
-
This model is battery powered and measures temperature using an external probe, providing cost-effective environmental monitoring ideal for inaccessible locations or where a faster response time is required.
-
Product
VHF Radio Direction Finding Antennas
Vector-Finder Series
-
The Vector-Finder Series of VHF direction finding antennas provide a compact, lightweight, active antenna, suitable for use in the field with handheld transceivers and scanning radios. The mechanical design allows the sense antennas to be folded back to provide a compact unit, easily stowed or transported in any vehicle. The system interfaces with any FM receiver or transceiver via the antenna jack and the earphone jack. Several different models are available to suit your pocketbook or unique field application, all of which operate on the phase shift technique. The VF-142Q models incorporate left-right indicators as well as an audible response from which the user can determine the true direction of the radio signal. The other types utilize the audible response generated by the equipment and heard on the user’s receiver or transceiver. All models operate from a 9-volt battery.
-
Product
15-CH Isolated Digital Output Module
ND-6056
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Transformer Insulation Testing
-
The primary test methods used to assess the condition of the active insulation components in transformers and bushings, on site, include:1) power factor/tan δ,2) variable frequency power factor/tan δ (1 - 500 Hz)3) dielectric frequency response (DFR) [a dielectric response method], and4) moisture in oil measurements (for transformers).
-
Product
Reusable ICP® Strain Gauge
-
This high-resolution dynamic alternative to bond foil strain gauges uses a quartz sensing element in a durable, titanium housing. It has 0.0006 microstrain resolution, 5 volt output, 100k Hz frequency response and 0.5 gram mass for lightweight test articles. The reusable sensor comes with a calibration certificate, attaches to the test specimen in 60 seconds and is removed in 10 seconds.
-
Product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Fiber-Optic Receivers
-
These New Focus high speed fiber-optic receivers offer bandwidths up to 38 GHz for receiving fiber optic data while delivering the lowest noise and cleanest responses possible.
-
Product
Earbud Function Button Tester
BK2121
-
The BaKo Type BK2121 was developed in response to Apple’s need to maintain quality control in earbuds which contain function controls and an internal microphone, designed to be used with newer IPods. It is a compact, easy to setup, easy to use machine with a short test time that you can use to functionally validate each earbud unit as it comes off the product line.
-
Product
Miniature Pressure Controller
VSO-HP
-
Parker’s VSO-HP is a compact electronic pressure control unit specifically designed for analytical and OEM instrument applications that require fast response and rapid pressure deflation.
-
Product
Software
-
The Circuit Sleuth API Tool Kit routines offer an alternative solution for users who prefer writing or need to write their own control programs, or have specific application needs for frequency response analysis. The “C” callable routines and DLLs provide direct access to the analyzer, enabling the user to control instrument functions and data management.
-
Product
16 Relay Output Board, 8 Isolated Digital Input Channels, 24V
APCI-2200-16-8
-
16 electromechanical relays with change-over contacts ? Max. switching voltage for the relays: 60 V/DC, 48 V/AC ? Max. switching current: 1 A ? Short response time ? Option: 8 input channels for AC voltage, optically isolated, input voltage range: 12 - 24 V DC ? Watchdog: software-programmable release, stop and time selection.
-
Product
Microwave Wideband PIN-TIA Receivers
MR22 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR22 series microwave wideband optical receiver, adopts High linear PIN diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
Product
Power Rail Probe, 6 GHz
N7024A
Oscilloscope Probe
The N7024A power rail probe is for users making power integrity measurements that need mV sensitivity when measuring noise, ripple and transients on their DC power rails. The probe is designed for measuring periodic and random disturbances (PARD), static and dynamic load response, programmable power rail response, and similar power integrity measurements. Many of today’s products have tighter tolerances on their DC power rails than the previous generations of these products, and the N7024A power rail probe is designed to help users ensure their products meet these tighter tolerances.
-
Product
ATX Motherboard With LGA1150 Socket 4th Gen Intel® Core™ Processor, Intel® Q87, USB 3.0, SATA 3.0, Dual LANs, DisplayPort, VGA, HDMI And MSATA
IMB211
-
The IMB211 is industrial-grade ATX motherboard with a full-range of integrated peripherals for general industrial and embedded applications. The IMB211 is based on 4th Generation Intel® Core™ i7/i5/i3/ Celeron® processors in LGA1150 socket with Intel® Q87 Express chipset. Four 204-pin DDR3-1333/1600 slots provide a maximum memory capacity of 32 GB to improve overall system performance. This industrial-grade high performance motherboard also supports Intel® Active Management Technology 9.0 (iAMT 9.0), SATA RAID, and triple-display capability through DisplayPort, HDMI and DVI-I interface. The board helps users to deploy more responsive, high-performance, graphic performance systems for advanced communication, gaming, industrial and automation applications.
-
Product
CAT-5 Video Receivers
-
Analog Devices high speed, differential CAT-5 video receivers and equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths. Our video receivers provide excellent common-mode rejection that enables the use of low cost, unshielded twisted pair cables in noisy environments.
-
Product
Ultra-thin Mass Flow Controller
DZ-100
-
The DZ-100 inherits the same CRITERION™ technology—a differential pressure detection system for laminar viscous flow ranges—used on HORIBA STEC’s MFC, the D500. This innovative technology controls the mass flow of various gases with high precision. As with the D500, the user-configurable DZ-100 supports multi-range and multi-gas applications. The compact design of the MFC reduces the internal volume of the internal gas flow path, and the optimized control algorithm improves response characteristics. It uses a compact CPU with high processing capacity, and the piezo drive circuit and control CPU are installed in the MFC module while the power supply components are housed in a separate small control box. Up to four MFC modules can be controlled by connecting them with the dedicated miniature connectors.
-
Product
Sound Level Meter, 30 dB, 130 dB, 1.5 dB, 0.1 dB, 0 °C, 40 °C
72-942
-
Compact Digital Sound Level Meter measures less than 9" in length, including the windscreen, yet provides selectable response time and frequency weighting. It is perfect for sound system testing, speaker system measurement and environmental noise level monitoring.
