Defect
other than specified, imperfection .
-
Product
Automated Stand for Magnetic Luminescent Control of Railway Wheels
-
The amount of information processed and time constraints required the creation of a multi-level distributed image processing system based on National Instruments Compact Vision System controllers, industrial computers and workstations. During the control process, the wheel is watered with a magnetic-luminescent emulsion, magnetized and exposed to ultraviolet radiation. As a result, the emulsion deposited on the defects glows in the visible range (yellow-green light). Eleven FireWire (IEEE 1394) color cameras with a resolution of 1280 x 1024 are used to scan the wheel surface. In one iteration, they completely cover a 20-degree sector of the wheel.
-
Product
Pipeline Defect Mapper
-
The non-intrusive measuring device takes measurements along the pipeline and plots the results directly onto the screen of the receiver. There is no need to carry extra logging and display devices. All the data is displayed and logged into the receiver for downloading to a spreadsheet or dedicated analysis program.
-
Product
Non-Destructive Testing (NDT)
-
Marposs complements its geometric measurement solutions with solutions for non-destructive testing using eddy current technology.The testing options can be divided in three large groups:Material integrity test, to check for the presence of defects (cracks, porosity, blow holes, inclusions) on the surface and in the layer just below the surface.Material properties test, to check if the thermal cycles (hardening, hardening and tempering, annealing, stress relieving, etc.) have been performed correctly. Material identification checks are done to sort parts with the same geometry but made with different materials.Thread inspection to check if the treading has been carried out and its quality.In addition to the non-destructive checks performed with the eddy currents, we have developed a durometer for the conventional measurement of surface hardness, according to the Rockwell scale (HRC or HRA); which uses a diamond penetrator to measure the hardness of the sample being tested.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
Portable GIS Partial Discharge Detector
JHPD-10
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
Product
Substrate Manufacturing
-
KLA’s substrate manufacturing portfolio includes defect inspection and review, metrology and data management systems that help substrate manufacturers manage quality throughout the wafer fabrication process. Specialized wafer inspection and review tools assess wafer surface quality and detect, count and bin defects during production and as a critical part of outgoing wafer qualification. Wafer geometry systems ensure the wafer shape is extremely flat and uniform in thickness, with precisely controlled wafer shape topography. Data analysis and management systems proactively identify substrate fabrication process excursions that can lead to yield loss. KLA’s substrate manufacturing systems support process development, production monitoring and final quality check of a broad range of substrate types and sizes including silicon, prime silicon, SOI, sapphire, glass, GaAs, SiC, GaN, InP, GaSb, Ge, LiTaO3, LiNBO3, and epitaxial wafers.
-
Product
Thermal Imaging Cameras
-
Thermography tools are indispensable when it comes to non-contact detection of thermal differences. Thermal imagers can be used to find defects in buildings, discover damage during maintenance, or analyze thermal processes.
-
Product
(AOI) Automated Optical Inspection Systems
-
For automated defect detection and high-accuracy measurements. VisionGauge Online High-Speed AOI systems are perfect solutions for demanding high-throughput, high-resolution applications. These systems are perfect for a wide range of applications including MicroElectroMechanical systems (for MEMS inspection or MEMS measurement), semiconductor & discrete device inspection and measurement.
-
Product
Constant Acceleration Tester-Arm Type
KRD31 series
-
KRD31 series constant acceleration tester are used to test articles under extreme acceleration conditions based on standard like MIL-STD-810F, MIL-STD-202 and IEC68-2-7. It is most suitable for testing electronic components or devices. Under high g effect on microcircuits, to check adaptability and reliability of wiring and the internal structures. It may expose mechanical and structural defects that are not found with vibration and shock tests.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Code Analysis
Kiuwan
-
Identify code defects & vulnerabilitesto manage your remediation effortsBlazingly fast analysis in a collaborative and unlocalized environment.
-
Product
Contour Check Round & Edge
-
Laser measuring systems are of central importance for rolling mills to check the contours of steel profile for defects during the production process. A slight deformation on the surface of the profiles reduces the quality of the product, and in the worst case, a broken roll can even destroy the entire batch. With our systems Contour Check Round & Edge you identify and evaluate deviations at an early stage. Increase the process efficiency of your production - regardless of temperature and profile shape.
-
Product
Environmental Stress Screening
E.S.S
-
King Design Industrial Co., Ltd.
E.S.S system could find most potential and hiding defects earlier by checking the physical property of allmaterials and components, and make use of their nature response under Environmental Stress. Through our screening will to pick out all potential and hiding defects in advance and improving the product's reliability inling. It benefits the manufacturer and customer mutually.
-
Product
VisualDetect basic
VDb-01
-
Hachmann Innovative Elektronik
VisualDetect basic is an easily operated voltage detector and interface-tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-tester warns against defect interfaces, whereas a dot matrix display shows the measured current [I/A] or frequency [f/Hz]. Thanks to the integrated configuration menu it can be adjusted to switchgears operated below nominal voltage on-site.
-
Product
Lab Inspection & Testing Services
-
Our lab services use advanced techniques to thoroughly inspect components for manufacturing flaws before assembly. We work with clients in the aerospace, automotive, oil & gas, manufacturing, wind energy, and various other industries to ensure their materials and components are free from defects that were introduced in forging or manufacturing processes.
-
Product
Companion Tool to VS for Test Time & Pin reduction
UltraScan
-
UltraScan is SynTest's solution to combat increase in test time. In 130 nm or smaller ? nanometer geometries, many defects become delay defects and it becomes necessary to use delay tests to detect the transition faults and path delay faults. Often bridging tests are also required.
-
Product
3D Sensors (Main Screen)
surfaceCONTROL
-
surfaceCONTROL sensors are used for 3D measurements and surface inspections. The sensors use the fringe projection principle to detect diffuse reflecting surface and to generate a 3D point cloud. This point cloud is subsequently evaluated in order to recognize geometry, extremely small defects and discontinuities on the surface. Sensors with different measurement areas are available. This enables the inspection of the finest of structures on components as well as shape deviations on large-area attachments. Powerful software packages are available for evaluation and parameter setting.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Semiconductor Wafer Microscope Inspection System
MicroINSPECT
-
MicroINSPECT Semiconductor Wafer Defect Microscope Inspection System combines state-of-the-art robotics, intelligent microscopes and SITEview software to provide a flexible, easy-to-operate defect inspection platform for either micro or macro defect wafer inspection.
-
Product
Precision LCR Meter (20Hz to 2MHz)
ST2840
-
ST2840 series pricision LCR meter innovatively adopts a new generation of technologies such as dual CPU architecture, Linux bottom layer, 10.1-inch capacitive touch screen, built-in instruction which effectively solves the defects of slow LCR test, single display and complicated operation in the past.The measurement frequency of ST2840 series is from 20Hz-500kHz/2MHz, which makes up for the shortcoming of lack of high-performance bridge in the frequency range of 500kHz.
-
Product
High Performance Programmable AC Power Supply
IT-M7700 Series
-
ITECH newly-launched IT-M7700 High Performance Programmable AC Power Supply combines intelligence and flexibility, breaks through the huge defects of the traditional AC power source, reduces the size to only 1⁄2 1U, maximizes space utilization. Built-in power meter and arbitrary waveform generator make it convenient to simulate various arbitrary waveform outputs. IT-M7700 is designed with advanced technologies of programmable AC and DC power supplies, and can be widely used in multiple fields such as power energy products, home appliances, industrial electronics, avionics, military and IEC standards testing.
-
Product
AutoGet auto Focus Portable Fiber Endface Inspector
CA3008
-
CA3008 Autoget is an intelligent portable fiber enface inspector. with newest hardware and software, and with functions of auto focus, auto exposure,auto analysis, autogenerate report, auto image transmission, etc. Autoget can clearly find out the defects of fiber endface, such dirts, scratches.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
Wafer Defect observing instrument
HS-WDI
-
Application■Semiconductor wafer■Solar wafer■Solar Cell■Thin-film Cell
-
Product
DC Magnetic Flux Leakage Testing
ROTOMAT / TRANSOMAT Product Family
-
Foerster Instruments, Incorporated
With the new generation ROTOMAT DA and TRANSOMAT DA flux leakage test systems FOERSTER is setting new standards in continuous quality assurance of ferromagnetic steel tubes. The test systems enable the reliable detection of natural and oblique defects, regardless of their angle or length, in addition to standardized longitudinal and transversal defects. The miniaturization of sensors together with highly integrated electronic components dramatically increases the number of channels. This makes a more precise and finer scan of the surface possible, giving a more complete set of information regarding detected defects. The newly introduced C-Scan visualizes these defects in high-definition and real-time, resulting in a completely new evaluation of the tubes to meet rising quality requirements.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
Assembly Testers
-
Systems that build products from components and then rigorously test them to ensure they function correctly, meet quality standards, and match specifications, preventing defects early in manufacturing through processes like electrical checks, functional tests, and physical inspections.
-
Product
Alternator/Battery Load Tester
6031
-
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
Product
19" 1He PCIe To PCIe Erweiterung With 4 PCIe X8 Gen-2 Slots
ExpressBox4-1U-xG2, EB4-1U-EXT
-
The PCIe Expansion ExpressBox4 1U-x8G2 provides a cost-effective path to expand your available number of PCI Express slots while maintaining a consistent server configuration. Magma products provide increased I /O capacity and scalability because multiple expansion systems can be combined to provide an almost unlimited number of PCI Express slots to a single computer. The ExpressBox4 is the only expansion solution that provides four full-length PCI Express slots in 1U rack-mount form factor. The enclosure includes a hot-swappable redundant power supply and hot-swappable cooling fans. The PCI Express slots are hot-swappable allowing you to replace a defective card without shutting down the system.
-
Product
PXI Fault Insertion Insertion Switch Modules
-
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
