Defect
other than specified, imperfection .
-
Product
Interoperability Testing Services
-
Using our decades of knowledge and experience of Bluetooth, markets and products we'll help you deliver products which are free of defects, minimize field issues, lower development costs and reduce time to market. Teledyne LeCroy offers test services to help in all stages of product development from Specification to Market Launch and beyond.
-
Product
Drone Inspection Software
Qii.AI
-
Qii.AI automates the detection and analysis of defects. It is the only enterprise AI platform that combines drone inspection software with an AI labeling tool, AI-assisted computer vision, and machine learning.
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
Website Testing Services
-
Our Free website verification testing service offers absolutely free usability andaesthetics critique as well as identifying up to 5 defects or issues.
-
Product
Thermal Cycling Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
Product
Highly Accelerated Life Testing (HALT)
-
Quickly validate reliability and identify manufacturing defects that could cause product failures in the field with MET’s Highly Accelerated Life Test (HALT)HALT technique uses a combination of accelerated stresses to expose product flaws early in the design and manufacturing stages, which improves product reliability and customer confidence inherent to the design and fabrication process of a new product as well as during the production phase to find manufacturing defects that could cause product failures in the field.
-
Product
Pruning Saw Control
-
Creation of a system that allows measuring the geometry of the board in the stream, determining the width of the wane, clean surface, the presence of large defects. Calculate the "net" width of the board and give signals for the movement of the saws to obtain the maximum output of the edged board of the given (standard) dimensions.
-
Product
Luminescence Defect Inspection System
INSPECTRA® PL Series
-
This system uses luminescent images created using photoluminescence (PL) to perform high-speed, high-sensitivity automatic inspection for crystal defects, cracks, and luminescence defects which cannot be detected with conventional visible light surface inspection!
-
Product
In-Line X-ray Inspection System
X-eye 6200
-
Automatically in-line inspect Solder joint defects of PCBA, and other defects on Hidden Components.Able to judge Good/NG fast with inspection speed of 1sec/FOV and the program can set ROIs conveniently.Performing X-ray inspection in various production site, integrated with other manufacturing equipements.
-
Product
Welding Resistance Tester
WRT
-
The Welding Resistance Tester is used in battery assembly lines to detect defective intercell connections. It is equipped with a 5-channel test head for car and truck batteries. It features 1-20 O DC resistance ranges and a multi-line LC display for OCV, CCV, and DCR measurements for 5 intercell connections.
-
Product
Vacuum Discharge Test Equipment
DAC-VD-1
-
DAC-VD-1 can locate defective points such as scars or pinholes on stator coils and wires easily.By applying voltage in a vacuum chamber, the electric arcing from a defective part can be discoveredvisually in a short time. DAC-VD-1 can be used widely in variety of applications from product developments to outgoing inspections.
-
Product
Automated Optical Inspection (AOI)
TR7700 SIII
-
TR7700 SIII is the newest generation of TRI's AOI solutions, delivering precise multi-phase inspection at full speed. By combining an ultra-fast camera, intelligent auto conveyor, and new GUI, the TR7700 SIII offers a powerful and easy to use AOI solution with fast programming, optimized board loading, production line integration and support for offline programming. TRI's new color algorithm combined with multiple lighting phases increase defect coverage and help deliver highly accurate inspection results with a minimum of false calls.
-
Product
Wafer & Die Inspection
-
SemiProbe wafer inspection system (WIS) examines, locates and identifies defects created during wafer manufacturing, probing, bumping, dicing or general handling. This provides microelectronic device manufacturers with accurate, timely quality assurance and process information. The WIS has single sided and double sided wafer mapping capabilities and can improve efficiency, reduce manufacturing costs, increase yields and shorten time to market.
-
Product
Contour Check Round & Edge
-
Laser measuring systems are of central importance for rolling mills to check the contours of steel profile for defects during the production process. A slight deformation on the surface of the profiles reduces the quality of the product, and in the worst case, a broken roll can even destroy the entire batch. With our systems Contour Check Round & Edge you identify and evaluate deviations at an early stage. Increase the process efficiency of your production - regardless of temperature and profile shape.
-
Product
Data Analytics
-
KLA’s data analytics systems centralize and analyze the data produced by inspection, metrology and process systems. Using advanced data analysis, modeling and visualization capabilities, our comprehensive suite of data analytics products support applications such as run-time process control, defect excursion identification, wafer and reticle dispositioning, scanner and process corrections, and defect classification. By providing chip and wafer manufacturers with relevant root cause information, our data management and analysis systems accelerate yield learning rates and reduce production risk.
-
Product
PocketDetect HR
PocketDetect HR
-
Hachmann Innovative Elektronik
With a PocketDetect HR you have a highly specialized, miniaturized and easy-going voltage detector at your fingertips. A thorough self-test ensures reliable function. A permanently enabled interface-tester warns against defect interfaces or residual voltages, while the low-power long-term display mode secures live working. The PocketDetect can be carried along due to its diminutive dimensions and lightweight (e.g. in the optional available belt case).
-
Product
Software
Interface Analysis
-
Surface-mount components warp during the reflow process, and the area where they attach also changes shape during assembly. This interface between components is where solder, paste, and gaps created due to thermal expansion combine to create 100% good products, or defects such as Head-in-Pillow, Shorts, and Opens. Fully understanding that critical interface between surfaces is more important than ever.
-
Product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
-
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
-
Product
Weatherometer with Air Cooling System, 80 Liters, 175 Liters, 225 Liters
-
Wewon Environmental Chambers Co, Ltd.
Weatherometer test is important to bring out the defects in something and to ensure its durability. The weatherometer result will make us identify those areas which need immediate improvements. But, there are areas where basic testing is not enough and does not do the job perfectly. To meet the high quality requirement, there is a need to perform extensive weatherometer testing on some materials. A place where such kind of testing is conducted is the xenon weatherometer.
-
Product
Flux Leakage Tester For Detecting Surface Defects In Hot Rolled Black Steel Bar
130MM ROTOFLUX® AC
-
Highly sensitive AC flux leakage is especially well suited to test hot rolled black steel bars and rods that have surface conditions which used to make finding shallow defects very difficult, if not impossible.
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
Automated Optical Inspection (AOI)
-
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
Product
Front-end
-
With geometries getting smaller, macro inspection becomes both more challenging and crucial for defect-free and high-yield wafer manufacturing. The variety of defects calls for detection optimization, fast screening and categorization of the high volume manufacturing environment, while maintaining high throughput.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Photomask Stations
-
Fast, sensitive, economic, off-line photomask defect review. Our 300 series photomask inspection and review stations use long working-distance microscopy and a unique four-way lighting system to greatly speed up location and identification of micron- and submicron-sized defects
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
Product
Dual Voltage Detector / Maintenance Tester
MicroPhase I
-
Hachmann Innovative Elektronik
MicroPhase I is an easily operated phase comparator, dual voltage detector and maintenance tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-testers warn against defect interfaces. The integrated "Universal Phase Comparator" compares two different interface signals, even if they are of different interface type or voltage. A unique error control avoids switching errors caused by erratic or unfeasible phase comparison.
-
Product
In-Line Test System
-
With an Averna in-line test system, clients boost production/yields, catch defects invisible to the human eye, reduce equipment downtime, and ensure repeatable results.
-
Product
Automated Marking Quality Control System
Angara
-
The machine vision system ASKKM "Angara" is designed to detect and reject defects in the marking of labels, excise stamps, boxes, vials, ampoules, bottles, etc., which have visual manifestations in the field of permanent or variable printing. It is installed on a conveyor or mounted in a labeling machine. Labels are checked before being applied to the product or marking on the package.
-
Product
Automated Optical Inspection System
AOI Series
-
Perform visual inspections of printed circuit boards (PCB) during manufacturing in which a camera is used to scan the board in extremely fine detail to check for any defects or failures.
