Common Core
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
6U VME 3rd Gen Core 17 Computer
VM6054
-
The VM6054 6U VME 2eSST Single Board Computer is built around Intel®’s state-of-the-art 3rd Generation Core™ i7 quad-core processor.
-
Product
PXI/PXIe RF Multiplexer, Quad 4-Channel, Terminated Common, 3GHz, 50Ω, MCX
42-876A-104
Multiplexer Module
The 40-876A-104 (PXI) and 42-876A-104 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 4 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI RF Multiplexer: 3 GHz, Quad 1 x 4, 50 Ω, Terminated Common
M9147A
Multiplexer Module
Route signals up to 3 GHz through any of four 1 x 4 RF switch multiplexers in a single PXI module.
-
Product
ARINC 818 Switch IP Core
-
ARINC 818-2 is a point-to-point, serial protocol, high bandwidth, low latency protocol for the transmission of uncompressed video, audio, and data during blanking period, widely used in AVIONICS application. Since a vast portion of the newer applications of the ARINC 818-2 have several displays with many channels of ARINC 818-2, switching has turned out to be more imperative. ARINC 818-2 switch can support up to 12 channels. Multiple switching modes such as broadcast, unicast, multicast, and mixed are also supported.
-
Product
X-Band Silicon Radar Quad Core IC
AWS-0103
-
The AWS-0103 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and dual beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
Product
Intel® 8th/9th Generation Core I 2U Fan System
EPC-P3066
-
Intel® 8th/ 9th Gen Core™ i processor (LGA1151) with Intel C246/H310Up to 4 x extension Card by Riser Card (Optional)3 x GigaLAN and upto 8 x USB3.02 x RS-232/422/485 and 4 x RS232 serial ports, 16 bit GPIO4 x SATA (max), 1 x M.2 E key, 1 x M.2 B/M key, 2 x F/S mSATAVGA+HDMI or 2 x HDMI output (Optional)12~24V DC input power rangeSupport Advantech I Door moduleSupport SUSI, WISE-DeviceOn and Edge AI Suite
-
Product
10th Gen Intel® Core™ Processor LGA1200
AIMB-287
-
Supports Intel® 10th Gen Core™ i processor (LGA1200) with Intel H420E chipsetTwo 260-pin SO-DIMM up to 32GB DDR4 2666/2933 MHz SDRAMSupports 1 M.2 M key, 1 M.2 E key, 4 COM, 6 USB 3.0 and 2 SATA IIISupports dual display of HDMI 2.0/ HDMI 1.4b/ eDPSupports TPM 2.0 (optional)THIN Mini-ITX with 12~24V DC InputSupport SUSI, WISE-DeviceOn and Edge AI Suite.
-
Product
LV Iron Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
Pre-Configured Core Test Sets
-
An In-Phase Core Test Sets provide you with a solid foundation and hardware framework to build your test set. Our pre-engineered Core Test Sets provide a completely integrated test set
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
Common Meter Reading Instrument - CMRI 1010
CMRI 1010
-
Signals & Systems India Private Limited
Common Meter Reading Instrument (CMRI) is a handheld computer used to download data from electronic tri-vector meters, supporting different protocols like IEC, ANSI and PACT. CMRI is also compliant to IS-15959/ DLMS (IEC-62056) standard. CMRI can be interfaced with the portable printer for spot billing applications.SANDS CMRI-1010 comes with LCD Graphical (3.5” TFT) & 15Line x 40 Characters visibility is rugged to withstand drop on to concrete and waterproof. CMRI is available with a memory size of 512 MB.
-
Product
LV Iron Core Motor Starting Reactors
-
Motor starting reactors are used to reduce voltage during starting of large 3 phase motors while limiting inrush currents.
-
Product
Intel® Core™ Ultra 3 Series Processor
AIMB-234
-
Intel® Core™ Ultra ProcessorsSupports Intel® ARC™ GPU with up to 12Xe, enabling four independent 4K displaysSupports up to 128GB dual-channel DDR5-7200MT/s using CSODIMM modulesBuilt-in NPU5 delivering 50 TOPS for dedicated AI accelerationOffers full support for embedded software APIs and Advantech’s WISE-PaaS/DeviceOn platformProvides extensive I/O expandability—2.5GbE, high-speed PCIe x8 Gen5, USB4 and USB3.2 Gen2 ports, plus SATA 3.0
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2310
-
CableTroll 2310 is an indicator for detection of earth faults (PtG) on multi-core and single core cable terminations. The unit uses NorTroll type current sensor (CT)
-
Product
NXP I.MX8M Plus Quad Core Processor Based IIoT Gateway Platform
MXA-200
IoT Gateway Platform
MXA-200 is an i.MX8M Plus based high-performance IoT gateway, which has an open platform design with Quad Core processor, two RS-232/422/485 isolated serial ports, two 10/100/1000 Ethernet ports, two USB 3.0 port and operating temperature range of -20~70°C. It offers two M.2 slots for integrating Wi-Fi/4G/5G modules. MXA-200 enables system integrators to develop applications precisely for renewable energy, EV charger, smart city and factories which require massive data collection, cloud based application and video related monitoring solutions.
-
Product
500 MHz 60 V Common Mode Differential Probe
DL05-HCM
Differential Probe
60 V of common mode and 80 V differential input range with 1 GHz of bandwidth, make these probes ideal for lower voltage GaN power conversion measurements. The 60 V of common mode is well suited for handling any float of the battery and bulk/absorption voltage during charging, while the 80 V differential input range provide margin for any overshoot.
-
Product
Ka-Band Silicon 5G Quad Core IC
AWMF-0108
-
The AWMF-0108 is a highly integrated silicon quad core IC intended for 5G phased array applications. The device supports four Tx/Rx radiating elements, includes 5 bit phase and 5 bit gain control for analog RF beam steering, and operates in half duplex fashion to enable a single antenna to support both Tx and Rx operation. The device provides 26 dB gain and +9 dBm output power during transmit mode and 28 dB coherent gain, 5.0 dB NF, and -28 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, Tx power telemetry, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
Product
Detection of PtG and PtP Faults on Multi and Single Core Cables
CableTroll 2350
-
CableTroll 2350 is an indicator for detection of PtG and PtP faults on multi and single core cables. The unit uses standard type current transformers. (40:1, 60:1 or 3x500:1)
-
Product
Ultra Compact, Uncooled Thermal Imaging Core
Dione S 1280 CAM Series
-
The Dione S 1280 CAM series is based on an uncooled 12 μm pitch microbolometer detector with a 1280 × 1024 resolution and NETD of less than 40 mK (available upon request) and 50 mK.The camera cores are optimized for low SWaP (Size, Weight and Power). The Dione S 1280 CAM is lightweight and small with mechanical shutter. It utilizes Xenics image enhancement for advanced image processing while keeping power consumption low.All Dione S 1280 versions have the same SAMTEC ST5 connector and are GenICam compliant. Dione S 1280 CAM is a LWIR uncooled thermal imaging SWAP module with housing supporting M34/M45 lens (optional).The ultra-compact Dione S 1280 CAM series find application in safety and security systems, as well as in industrial thermal imaging systems.
-
Product
Processor Intel Core I7, PCI Gen 3, AMC
AMC726
-
The AMC726 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® 4th generation Core i7 Processor (Haswell) with QM87 PCH. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
Product
Common Metallic Pendulum Impact Testing Machine
JB-(C/D)
-
Jinan Testing Equipment IE Corporation
KB- (C/D) common type metallic pendulum impact testing system is the basic model for impact tester. The metallic pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and capable of doing a large number of impact tests continuously. The display method for the models is different, respectively there are analog dial display, touch screen digital display and computer display. For the later two models, it can display the impact power, impact toughness, and pendulum rotation angle. All the testing reports can be printed out. The metallic pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
Product
11th Gen Intel® Core™ I5-Based Fanless Embedded Computer
EMP-510 Series
Box PC
- 11th Gen Intel® Core™ i5 BGA SoC processor- DDR4 SODIMM up to 64GB- FHD/4K/8K up to 4x independent displays- 2x GbE, 1x COM, 4x USB ports- M.2 2280 SSD- Wi-Fi 6/LTE compatibility
-
Product
Air Core Test Lab Reactors
-
Test Laboratory Reactors are designed for high voltage and high power test laboratories. They are designed to withstand the most extreme electrical service conditions during test periods. Design techniques are implemented in accordance with the most demanding service conditions. These reactors are used for various purposes in test laboratories such as current limiting and synthetic testing of circuit breakers, capacitor testing, artificial line simulation etc.
-
Product
12.1" Fanless Panel PC With Intel® Core™ I5-7300U Processor
PPC-412
Panel PC
12.1" XGA TFT LCD with resistive touchscreenIntel® Core™ i5-7300U(default); i7-7600U/i3-7100U(optional) processor with fanless system design1 x isolated RS-422/485 with auto flowWide input power range (9 ~ 32 VDC)Dual Gigabit Ethernet with IEEE1588 support3 x Independent displays1 x M.2 bay (2242) for storage only and support SATA RAID 0/1No RED CertificationSupports VESA 75 mounting interface
-
Product
PXI 5A Power Multiplexer, 4-Bank, 11-Channel, Isolated Common
40-651A-013
Multiplexer Module
The 40-651A-013 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
IP Core and FPGA Products
-
Our FPGA offerings include development boards and IP cores for Altera FPGA devices. The IP cores include: I2C, PCIe, JPEG-LS, LVDS Camera Link and memory controllers.
-
Product
12.1" Panel PC With 8/9th Generation Intel® Core™ I/Celeron® Processor
PPC-6121
Panel PC
12.1" TFT XGA LCD panel with resistive touch control8/9th generation Intel® Core™ i/Celeron® processor (thermal power design: 35W)2 x 260-pin SO-DIMM DDR4 2666 MHz (max. 32 GB)1 x M.2 2230 (E key)1 x mSATA bay (SATA SSD + mSATA support RAID 0&1)1 x Optional TPM2.0 & 1 x Optional PCI/PCIe x4 expansion kit1 x Isolated RS422/485 (terminal block)1 x VGA and 1 x HDMI
-
Product
6th Generation Intel® Core™ i7/i5/i3 Processor-Based Fanless Embedded Computer
MXE-5500 Series
Industrial Computer
ADLINK's new Matrix MXE-5500 series of rugged quad-core fanless computers features the 6th generation Intel® Core™ i7/i5/i3 processors, delivering outstanding performance with robust construction.
