-
Product
Fixturing Kit
10744A
Test Fixture
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
SMD Test Fixture
16034G
Test Fixture
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
Product
Fixture Interface Module 2 Test Matrices
OTP2 module no.193
Interface Module
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
-
Product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
-
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
Product
9050 - 50 Module, 2-Tier Solution
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
-
-
Product
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA
910121178
Soldering Fixture
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA.
-
Product
Test Fixture, Axial And Radial
16047A
Test Fixture
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
Terminal Block
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
9025 Slide Mount
-
The 9025 Slide Mount was developed to provide maximum versatility and easy access to instrument-side wiring and cable assemblies. Ordering is simple: the 9025 Slide Mount s is offered as a package that includes the receiver, flanges and instrument bracket. The only to determine is the type of slide kit needed. VPC offers a selection of slide kits designed to fit most common rack depths. Slides are rated to support 180 lbs (81 kg) to accommodate large fixtures.
-
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Customized Test Fixtures
-
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
Manual Test Fixture (MA)
MA 2013/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 25,00 kg
-
Product
Manual Fixture Kit
230371 – CMCSK-02-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Kelvin IC Clip Lead
16089C
Accessory Kit
Measure odd-shaped components that you cannot measure using conventional fixtures
-
Product
Manual Fixture Kit
230353 – CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Millimeter-Wave Automated Accelerated Reliability Test Systems
nm-Wave AARTS System
-
AARTS fully integrated, automated, turnkey system provides flexibility and accuracy in determining RF and DC performance degradation with aging to predict life expectancy for compound semiconductor devices. Our millimeter-wave Automated Accelerated Reliability Test Systems (AARTS) and fixture solutions are available in standard frequency ranges from 26.5 to 67 GHz.
-
Product
Test Fixture
16047E
Test Fixture
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
Product
ITA, 9050, 50 Module, VXI and Discrete Wiring, Double Tier
410104538
ITA
The 50 module ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC front or rear mount enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration.
-
Product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
-
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
Ballistic Test Equipment
-
n 1998, H-S Precision introduced ballistic range equipment and fixtures designed to compliment its line of ballistic test barrels. Equipment is available for pressure and velocity testing, NIJ body armor testing, ballistic armor testing and extreme accuracy testing. We are the leading supplier and producer in the World for the ballistic test barrels. The most well known ammunition companies use H-S barrels for testing the quality and consistency of their ammunition.
-
Product
Ionization Test Set
PFK-105
-
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
