Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
3U CompactPCI® Serial XMC Module Carrier Blade
cPCI-A3XMC
Carrier Board
- 3U 4HP CPCI-S.0 peripheral- One XMC slot- Operating temperature: -40°C to 85°C with qualified components
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 57610
-
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
Product
Isolated RS-422/485 Communications and Watchdog Card
WDG-SIO
-
This multifunction card contains a Watchdog Timer, an RS422/485 Serial Communications port, and an internal Temperature Alarm. The WDG-SIO is a full-length card that installs in “long” expansion slots of IBM PC/XT/AT and compatible computers. The following paragraphs describe functions provided by the WDG-SIO card.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Serial Device Servers
-
Advantech''s serial device servers, Modbus gateways, and USB Device Server are easy to install and configure, support wired and wireless networking and provide various operation modes to satisfy rigorous industrial automation needs.
-
Product
64-Channel Boundary-Scan Digital I/O Scan Module
JT 2111/MPV DIOS IDC
Digital I/O
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
Product
Mixed Signal Oscilloscope - 1.5 GHz, 4 Analog Plus 16 Digital Channels
MSOX4154A
Oscilloscope
1.5 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
CPCI Based 486DX4 Board
MS 1501
-
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
Product
Universal Checkback Standalone System
UCBS
-
The Universal Checkback Standalone System (UCBS) provides periodic testing of "ON-OFF" carrier sets other than the TC-10B and the UPLC/UPLC-II (which incorporate this same checkback tester internally). The UCBS determines the functionality of the complete channel including the transmitters, receivers and associated coupling equipment. Periodic testing is required for the normally "off" channel, to provide warning of signal deterioration prior to needing it for relaying, The UCBS facilitates automatic testing of the channel at preset intervals. The UCBS is totally field programmable. All programming is done with a computer using the RS232 serial port or limited factory settings with switches on the Checkback module. Front panel LEDs indicate the factory or custom setting applied and the status of alarms.
-
Product
Ethernet, GPIB And USB To Serial Interface Board
-
ICS's Model 9006 is a multi-interface to serial board that adds Ethernet, GPIB and USB interfaces to serial devices or older instruments. Use with an embedded processor board to create smart instruments with multiple interfaces. The 9006's Ethernet port is VXI-11 compatible for easy control by the following computer systems without special drivers: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems. VXI-11 is one of the 9006's Ethernet protocols. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
Product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Two DUC (digital upconverters)- Four 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Oscilloscope: 100 MHz, 4 Analog Channels
DSOX2014A
Oscilloscope
100 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 3U VPX
Model 52141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
MIL-STD-1553
-
CAES SµMMIT™ Interconnect Products provide an intelligent solution to address MIL-STD-1553 multiplexed serial data bus challenges in avionics and spacecraft onboard data handling subsystems for both military and civil applications.
-
Product
Pattern Generator
PI-2005
-
As a test engineer or digital designer you must have state-of-the-art tools to test, characterize and verify your complex semiconductor devices and digital circuit boards. The PI-2005 Pattern Generator will generate a wide range of simple or complex digital patterns for any test application that requires a serial or parallel digital data stream. To meet the requirements of complex devices and digital circuits, the pattern generator can be configured from 16 to 64 output channels.
-
Product
8-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 58671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 1.25 GHz 16-bit D/As- Eight digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Quad µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
DH Series High-Sensitivity Solder-In Tip, 30 GHz BW, 2.0 Vpp Range
DH-SI-HS
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
High Quality Switch Power Supply
CX-P60
-
Shenzhen Chuangxin Instruments Co., Ltd.
high quality switch power supply. This serial single output switch power supply is a kind of DC regulated power supply with high efficiency and stability.
-
Product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-7 FPGA - 6U VPX
Model 58720
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- One or two DUCs (Digital Upconverters)- Two or four 800 MHz 16-bit D/As- 4 or 8 GB of DDR3 SDRAM Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connectionsto the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Oxygen Analyzer
DT3000
-
The Datatest Model DT3000 is a Zirconia sensor, microprocessor based, oxygen analyzer. The DT3000 comes with probe configurations for temperatures up to 3200F. The microprocessor based controller provides long-term stability and reliability, plus optional features for controlling back purge, calibration gas injection, and self-calibration. 4 - 20 mA output and Modbus RTU serial port are standard. The DT3000 is available in either a NEMA 4 wall mount or panel mount configuration.
-
Product
Efficiency And Innovation, Squeezed Into One Tiny, Affordable Package
LatticeECP3
-
*Up to 16 channels at 3.125 Gbps*800 MBps DDR3, 1Gbps LVDS*Up to 586 programmable sysIO buffers with support for PCI Express, Ethernet (GbE, XAUI, & SGMII), HDMI, SMPTE, Serial Rapid I/O, CPRI and JESD204A/B and more*Up to 150 k LUTs and 6.8 Mbits of SRAM*Wide array of packages as small as 10.0 mm x 10.0 mm with power consumption below 0.5 W
-
Product
10-Pin RJ50 Male to 25-Pin DB-25 Male Serial Cable
182846-02
Serial Cable
Serial conversion cable for 4-port serial board to a DB-25 male connector.
-
Product
Switching Unit
ZET 454
-
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
Product
Mezzanine Module
RS485-MOD2
-
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
Product
Annunciator
DMS 3K
-
The AMETEK DMS 3K is a flexible, remote alarm management system. It captures alarms from digital or analog inputs, displays alarms on the built-in web server and provides outputs to remote annunciator displays and other devices using serial and Ethernet communications. Alarms can be time stamped to the millisecond for sequential events recording and email notification can be provided for critical events.
-
Product
GPIB-RS485/RS422 GPIB Instrument Control Device - Taiwan 110VAC
779733-11
GPIB Controller
The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
CPCI ARM LPC3250 Board
MS 1513
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
Plug & Play JTAG/SWD Microcontroller Debugger with Built In GDB Server & UART
Black Magic Probe V2.3
-
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
