Product

Vibration Transmitters

-

Metrix

Metrix

Metrix* proximity vibration transmitters are compatible with Bently Nevada** Series 3300, 7200, and 3000 probes and cables as well as our own probes and cables. The flexible Metrix MX2034 Transmitter can be reconfigured to handle any of these probe / cable combinations.

Product

Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV

RP4060

-

Teledyne LeCroy

RP4060 - Teledyne LeCroy

+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).

Product

Portable Calibration Shaker Table

AT-2030

-

Agate Technology

AT-2030 - Agate Technology

The AT-2030 portable calibration shaker table is designed for simple accelerometer and vibration transducer calibration without the need for advanced features. AT-2030 shaker table and vibration calibrator is a variable frequency, variable amplitude, battery operated portable shaker capable of calibrating accelerometers, transducers, and proximity probes. Applications are producing a known vibration signal in g’s, mils, or ips for sensor, wiring, instrumentation, and system checkout in vibration condition monitoring applications.

Product

Probe Placement JIG

456 & 355

-

Elcometer Limited

456 & 355 - Elcometer Limited

The Elcometer Probe Placement Jig is the ideal accessory for measuring coatings on small or complex components when the highest levels of repeatability and accuracy are required.

Product

Current Probe With Hall Effect Technology

CP 35

-

GMC-I-PROSyS

CP 35 - GMC-I-PROSyS

The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.

Product

Quad Input Logging Thermometer

DT304

-

UEi Test & Measurement Instruments

DT304 - UEi Test & Measurement Instruments

This series of Digital Thermometers offers a unique combination of features including logging capabilities with 9,999 memory positions and a USB interface and software, one, two and four inputs offering relative and differential readings. The Apollo also offers a solution to storing probes and is manufactured to conform to the IP67 standard, meeting performance expectations of water submersion and high-pressure dust resistance

Product

Ultrasonic Immersion Probes

SONOSCAN I

-

SONOTEC GmbH

SONOSCAN I - SONOTEC GmbH

The SONOSCAN immersion transducers for Non-destructive Testing (NDT) are mainly used to test metals and plastics for the smallest material defects. For example, binding defects, welding defects or cracks and pores in metal parts can be detected. The powerful, robust ultrasonic probes can be connected to all common ultrasonic testing devices. Due to variable designs and sizes, the immersion probes guarantee optimal use. In addition to ultrasonic standard pobes, we also offer customized transducers according to your individual specifications.

Product

Test Contactor/Probe Head

cBoa

-

Cohu, Inc.

cBoa - Cohu, Inc.

cBoa™ test contactors and probe heads are the solutions for contacting high-frequency devices for package test or final test at wafer. The robust design and materials of the cBoa probe withstand the rigors of high-volume test by providing longer life and higher yield. The homogeneous DUT side plunger provides longer run times between cleaning and increased probe life.The cBoa features a stainless-steel spring for tri-temp testing and performs in operating temperatures of -55°C to +155°C and bandwidth of up to 35 GHz @ -1 dB.

Product

WiFi Inspection Cameras

-

General Tools & Instruments

General Tools & Instruments

WiFi Inspection Cameras generates a local WiFi hotspot (without Internet access) through which video clips and still photos of hard-to-reach or hard-to-see areas or equipment captured by the probe camera can be sent to an app-enabled smartphone or tablet for viewing and sharing. Free apps for iOS devices (iPhones or iPads) and Android devices are available from the iTunes App Store and Google Play Store, respectively. The three WiFi cameras differ in probe length, camera lighting and grip style.

Product

Universal CMM Software Module

Verisurf CMM

-

Verisurf Software, Inc.

Verisurf CMM - Verisurf Software, Inc.

Plug and play CMM communication for Hexagon Dea, Leitz, Mitutoyo, Wenzel, Pantec, Nikon, LK or Zeiss™️ machine controllers, as well as Renishaw, Tesa, Hexagon Leitz or Zeiss™️ head controllers.Optional support for scanning probes and error mapping compensation for geometric, volumetric, orientation, positioning and kinematic errors in the CMM structure that affects accuracy.

Product

Test Port Cable, 1 Mm

11500K

-

Keysight Technologies

11500K - Keysight Technologies

Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum

Product

Probe Card

VC20E Series

-

Celadon Systems, Inc.

VC20E Series - Celadon Systems, Inc.

The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.

Product

Terminal Test Kit (94 Pcs)

3601

-

Peaceful Thriving Enterprise Co Ltd

3601 - Peaceful Thriving Enterprise Co Ltd

*Total: 94 pcs*Alligator Clip x 2 pcs*Testing Probe x 2 pcs*Flat Terminal x 48 pcs*Testing Needle x 4 pcs*1 to 2 Connector x 2 pcs*Round Terminal x 24 pcs*5K Variable Resistor x 2 pcs*Polarity Tester / Stroboscope x 2 pcs*Insulator Pierce Through Clip x 2 pcs*SRS Air Bag Replacement Connector x 2 pcs*Male / Female to Male / Female Extension Wire x 4 pcs

Product

Bulk Current Monitoring Probe

MP-50

-

FRANKONIA GmbH

MP-50 - FRANKONIA GmbH

The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.

Product

Pilot Control Software Suite

-

SemiProbe

SemiProbe

The SemiProbe PILOT Control Software Suite semiautomatic and fully automatic probe systems employs the SemiProbe patented Adaptive Architecture. Software modules can be added to the base system as needed. PILOT Control Software consists of a Microsoft Windows-based user interface built on the SemiServer application for communicating to and from the probe system. Individual customer applications can be integrated with PILOT Control Software for a customized system to meet individual needs.

Product

Temperature and Humidity Probe

T0211-2

-

COMET SYSTEM, s.r.o.

T0211-2 - COMET SYSTEM, s.r.o.

Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.

Product

High 1.73 (49.00) - 8.00 (127.00) High Performance Lead Free Probe

LFRE-1I35-8

-

ECT

LFRE-1I35-8 - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Differential Probe

DP-60HS

-

PINTEK Electronics

DP-60HS - PINTEK Electronics

*High Sensitivity Model: x 1, x 5, x 10 Attenuation*1 MΩ // 10PF Input Impedance*High Frequency Operation: x 1(30 MHZ), x 5(60 MHZ), x 10(60 MHz)*Especially For Low Voltage: x 1(7 Vp-p), x 5(35 Vp-p), x 10(70 Vp-p)

Product

ICT Probes

Merica Serirs- MP175

-

Merica Technology Ltd

Merica Serirs- MP175 - Merica Technology Ltd

Minimum Center: 1.91mm (75mil)Current Rating: 3amps, continuousContact Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.40mmRated Stroke:4.30mmSpring Force: 203gf (7.2oz)/227gf(8oz)

Product

Advanced Stand-Alone AFM

SmartSPM

-

HORIBA, Ltd.

SmartSPM - HORIBA, Ltd.

The SmartSPM Scanning Probe Microscope is the first 100% automated system that offers its cutting-edge technology of ultra-fast, metrological and high-resolution measurements for the most advanced materials research at the nanoscale in all AFM and STM modes. With the SmartSPM zooming in from large up to 100 µm overview scans down to atomic resolution has become a reality. Its design has been specially developed to be capable of being seamlessly integrated with optical spectroscopies (SNOM, Raman, Photoluminescence and TERS/SERS techniques).

Product

Logic Analyzer

TLA7000

-

Tektronix, Inc.

TLA7000 - Tektronix, Inc.

The modular TLA7000 Logic Analyzer Series provides the speed and flexibility you need to capture logic detail on today's fastest microprocessors and memory designs. Pinpoint the source of elusive errors and gain the visibility you want with large easy-to-read displays, fast data throughput, and time-correlated views of analog and digital signals through the same probe.

Product

Changeable Cassette

230372/1 – CMCSK-03-01

-

Columbia Elektronik AB

230372/1 – CMCSK-03-01 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.