Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
product
Diode Scanner
SC924
Frothingham Electronics Corporation
The SC924 is an electromechanical device for testing diodes loaded on burn-in boards.A set of Kelvin contacts is indexed from diode to diode. The contacts move over a range of 24 inches in the X direction and the table holding the boards moves over a range of 9 inches. This allows scanning of multiple burn-in boards or boards with multiple rows of diodes.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Elastomeric Contact
High performance contact materials specially designed for the advanced needs of the electronic industry. PariPoser Interconnects makes electrical connections uniformly between opposing contact areas using conductive columns, which are regularly distributed within a sheet of advanced polymer. PariPoser Interconnects is custom formulated depending on the application’s design rules.
-
product
Surface Cleanliness Analyzer
Surface Analyst
The Surface Analyst is a fast, easy, accurate, and non-destructive instrument that quantifies your level of surface preparation from the lab to the manufacturing floor. In 2 seconds, the Surface Analyst determines the surface cleanliness level by providing the contact angle measurement and a pass/fail result.
-
product
Network OTDR
NFO series
The NFO OTDR unit injects the laser pulse into the fiber under test and picks up scattered and reflected optical signals by an avalanche photodiode (APD). The unit accepts remote commands from Internet to control all related timing and data acquisition processes. Maximal three wavelengths are available at the NFO with options on 1310, 1490, 1550, and 1625 nm. NFO also has options on dynamic ranges so users can select the most cost effective units for their demands. Radiantech provides an easy use API (Application Program Interface) for NFO so users can design and build their own AP for NFO. Standard NFO API package is for Windows XP or higher. Please contact Radiantech’s sales person to inquire API for another OS.
-
product
High Power, Quick Release Circular Connectors
HBB Series
HBB Series high-power, quick-release harsh-environment connectors are available in both single and five pole version. The series has a compact robust RoHS design in a metal shell with polarization, user-friendly push-lock mating, and quick-release unmating mechanisms, sealed IPx7 and IP6K9K when mated, high-reliability Hypertac hyperboloid contacts rated for up to 500A, and 360º shielding.
-
product
Alternate 24.00 (680.00) - 96.00 (2722.00) Godzilla High Current Probe
HC375F-6
Current Rating (Amps): 100Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 360Full Travel (mm): 9.14Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,110Overall Length (mm): 78.99
-
product
Digital Tachometers
Kusam Electrical Industries Limited
KUSAM-MECO Digital Tachometers - no contact, contact, non-contact/contact
-
product
Mini Pneumatic, Contact, Receiver, Push-in Fitting, for 6 mm OD Tubing
610131112
Primary mating contact 610132112.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
product
ULTRA® Contactors
ULTRA CONTACT Series offers high yield, durability and consistent performance under the most demanding testing environment. Our design offers easy integration to most test handler platforms and on automotive devices.
-
product
H.V. Probe Meter
PD-40AM
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
-
product
Complete Probe Station
BD Series
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
product
20-Pin GMCT Male Connector, 10A, Without Backshell
92-960-020-10A-M
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
48 Channel Relay Output Module
DP-VME-4059
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
product
Plugbord
4112-4
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. Zig-Zag Bus Pattern on wiring side.Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions. Continuous ground plane on component side with 0.085” etched clearance area around each hole Row and column legends provided
-
product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers
310104368
The 50 Module Receiver is a rugged system devised to accommodate high I/O. With high contact point availability, the 50 Module Receiver is suited for larger test and measurement systems. Both tiers are designed for discrete wiring, and can accommodate individual 9025 ITAs.
-
product
PXI/PXIe 64x4 High Density Matrix Module, 1-Pole, 2A, 60W
42-585A-001
Our model 40-585A, along with the following models 40-584A, 40-586B and 40-587A are high-density single pole PXI matrices each with 256 crosspoints. All models use gold-plated contact electromechanical relays. This module is also available in PXIe format (42-585A-001).
-
product
Receiver, G6, 6 Module, EMI
310104344
The G6 Receiver includes a keying feature, locking handle and nickel-plated steel slides that engage up to 1,440 signal contacts in a 6-module configuration- all in a compact and rugged design.This G6 model also includes EMI gasketing for EMI protection.
-
product
Spring Loaded Contacts
ATE Probes, Pogo pins and Contact Pads. Gold-plated, spring-loaded, capable of thousands of cycles. Probes for Automated Test Equipment (ATE). Various height SMT contact pins. Flat SMT contact pads. Spring loaded contacts consist of a plunger (or head), barrel (or body), and a fully encapsulated fine spring, to provide the spring force required to maintain positive contact. All have a high durability, exceeding 10,000 mating cycles.
-
product
Pneumatic Contact, ITA, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610132104
Primary mating contact 610131104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
product
AC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Measures AC voltage and current without contacting condutors.
-
product
Needle Microprobe
MT-29/1HT
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
USB-Micro Type B Test Connector
Test connector for Micro USB Type B (5 pole) for contacting Micro USB interfaces. Application in smaller USB devices like cameras, mobile phones, radios, hard disks, etc.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Dip Clip, 14 Pin With Nickel Silver Contacts
5014
Pomona DIP Clip test clips are designed fortesting dual-in-line IC packages on PC boards. Thesedevices incorporate many built-in features that assurea positive electrical connection as well as hands freetesting.
-
product
Cantilever Probe Cards
Cantilever Probe Cards are based on the approved epoxy ring design. The probe-needles are precisely arranged the required pattern to ensure proper contact on the pads.
-
product
Receiver, D16, 16 Modules, 90 Series Modules
310131111
The D16 receiver frame accepts sixteen 90 Series modules and can engage up to 3,840 signal contacts.
-
product
Selector Switches
Elma offers a wide range of dimensions, number of switching positions and contact arrangements. Our selector switches continue to be the foundation of Elma's longstanding reputation for quality, feel and reliability.
-
product
Plugbord
4066-4
VECTOR Electronics and Technology, Inc.
72 Gold plated edge contacts (36 each side)on 0.100"(2.54mm) centers. Overall ground plane on wiring side. Interleaved zig-zag bus pattern on component side.0.085” diameter etched clearance area around each hole on ground plane sideBus and plane surface solder coated for user convenienceRow and column legends provided
-
product
Spread Resistance For Slanting Polished Sample Of Semiconductor By Tow Kinematically-mounted Probe Contacting .
SRS-2010
*Resitivity map along with depth direction, thickness of epitaxial , depth of PN junctin and carier density profiles
